Integrated Amplifier (Tube)

RAYSONIC SE-20
MADE BY CANADA
Features:
SOLD
MADE BY CANADA
Features:
- Class A, triode, single-end design.
- Output power: 8 watts x 2 channels.
- Extended frequency range output transformers.
- Heavy duty power transformer.
- All single paths are point to point wiring.
- Two 300B power tubes are individually biased
- Circuit built with high quality electronic components.
- All-aluminum chassis.
- Chassis finish: silver.
- Vacuum tubes: 300B x 2, 6SN7 x 2, 6SL7 x 2.
- Output power: 8w x 2 channels.
- Input sensitivity: 270mv.
- Input impedance: 100kΩ.
- Harmonic distortion: <1%.
- Frequency response: 5HZ - 42KHZ ±1dB.
- S/N ratio: 85dB.
- Input: 4 sets.
- Speaker output impedance: 4 or 8 ohms.
- Power consumption: 126 watts.
- Dimensions: 43L x 30W x 20.5H (cm).
- Operating Voltage: 100-120VAC. 50Hz/60Hz (220-240VAC 50Hz/60Hz).
- Weight: 25kg.
SOLD
Integrated Amplifier

Integrated Amplifier (Tube)

ROGERS E40A
MADE IN UK
SPECIFICATIONS :
Designed and built for digital era, the Rogers E-40 and E-20a Class 'A' Stereo Integrated Amplifiers truly represent digital sound the way it should be heard and appreciated.These superb fully integrated, all-valve, handmade amplifiers are guaranteed to send tingles down the spine of the most discerning of audio aficionado's. Recommended for use with a wide range of the highest quality transducer or electrostatic speakers.
Power : 40 watts per channel class 'A' Valve
Output : Push Pull Cathode Follower
Self Bias 6L6GT x 8
Phono Stage : 2 x ECC83/12AX7
Line Input Impedance : Phono: 47K ohms, Line: 100K ohms
-----SOLD-----
MADE IN UK
SPECIFICATIONS :
Designed and built for digital era, the Rogers E-40 and E-20a Class 'A' Stereo Integrated Amplifiers truly represent digital sound the way it should be heard and appreciated.These superb fully integrated, all-valve, handmade amplifiers are guaranteed to send tingles down the spine of the most discerning of audio aficionado's. Recommended for use with a wide range of the highest quality transducer or electrostatic speakers.
Power : 40 watts per channel class 'A' Valve
Output : Push Pull Cathode Follower
Self Bias 6L6GT x 8
Phono Stage : 2 x ECC83/12AX7
Line Input Impedance : Phono: 47K ohms, Line: 100K ohms
-----SOLD-----
Integrated Amplifier (Tube)

AUDIO RESEARCH CA50
MADE IN USA
SPECIFICATIONS :
Power output : 45 watts per channel continuous from 20Hz to 15kHz. Approximate actual power available at "clipping" 50 watts (1kHz)
Power bandwidth : (-3dB points at 1 watt) 18Hz to 40kHz
Frequency response : (-3dB points at 1 watt) 2Hz to 50kHz
Input sensitivity : 0.3V RMS for rated output. (35dB gain into 8 ohms (optional 38dB))
Input impedance : 100K ohms Single-ended
Output taps : 8 ohms, 4 ohms
Output regulation : Approximately 1.0dB 8 ohm load to open circuit
Overall negative feedback : 7 dB
Damping factor :13
Distortion : 1kHz total harmonic distortion typically 2% at 45 watts, below .05% at 0.1 watt
Slew rate : 10 volts/microsecond
Rise time :5 microseconds
Hum & noise : Less than 1.0mV RMS 85dB below rated output (IHF weighted, input shorted)
Power supply energy storage : 183 joules
Power requirements : 105-125VAC 60Hz (210-250VAC 50Hz) 290 watts at rated output, 330 watts clipping, 190 watts at "idle"
Tube complement : (2 matched pairs) 6550C power output, (2) 6922 driver, (2) 6922 input
Dimensions : 19" (48.3 cm) W x 7" (17.8 cm) H x 15" (38.1 cm) D. Handles extend 1.5" (3.8 cm) forward
Weight : 43 lbs. (19.5 kg) Net; 56 lbs. (25.5 kg) Shipping.
-----SOLD-----
MADE IN USA
SPECIFICATIONS :
Power output : 45 watts per channel continuous from 20Hz to 15kHz. Approximate actual power available at "clipping" 50 watts (1kHz)
Power bandwidth : (-3dB points at 1 watt) 18Hz to 40kHz
Frequency response : (-3dB points at 1 watt) 2Hz to 50kHz
Input sensitivity : 0.3V RMS for rated output. (35dB gain into 8 ohms (optional 38dB))
Input impedance : 100K ohms Single-ended
Output taps : 8 ohms, 4 ohms
Output regulation : Approximately 1.0dB 8 ohm load to open circuit
Overall negative feedback : 7 dB
Damping factor :13
Distortion : 1kHz total harmonic distortion typically 2% at 45 watts, below .05% at 0.1 watt
Slew rate : 10 volts/microsecond
Rise time :5 microseconds
Hum & noise : Less than 1.0mV RMS 85dB below rated output (IHF weighted, input shorted)
Power supply energy storage : 183 joules
Power requirements : 105-125VAC 60Hz (210-250VAC 50Hz) 290 watts at rated output, 330 watts clipping, 190 watts at "idle"
Tube complement : (2 matched pairs) 6550C power output, (2) 6922 driver, (2) 6922 input
Dimensions : 19" (48.3 cm) W x 7" (17.8 cm) H x 15" (38.1 cm) D. Handles extend 1.5" (3.8 cm) forward
Weight : 43 lbs. (19.5 kg) Net; 56 lbs. (25.5 kg) Shipping.
-----SOLD-----
Integrated Amplifier (Tube)

RAYSONIC SA-30A
Features:
Class A, triode, single-end design
Output power: 18 watts/per x 2 channels.
Extended frequency range output transformers.
Heavy duty power transformer.
All single paths are point to point wiring.
Six EL34 power tubes are individually biased.
Circuit composed of High Quality Electronic Components.
Chassis finish: silver.
Specifications:
Vacuum tubes: EL34 x 6, 12AX7EH x 2, 12AU7EH x 2, 5U4 (5Z3p) x 2.
Output power: 18w per channel x 2
Input impedance: 100kΩ
Conditions : Pre-Owned, Mint
Price : Rp 19.000.000,-
Features:
Class A, triode, single-end design
Output power: 18 watts/per x 2 channels.
Extended frequency range output transformers.
Heavy duty power transformer.
All single paths are point to point wiring.
Six EL34 power tubes are individually biased.
Circuit composed of High Quality Electronic Components.
Chassis finish: silver.
Specifications:
Vacuum tubes: EL34 x 6, 12AX7EH x 2, 12AU7EH x 2, 5U4 (5Z3p) x 2.
Output power: 18w per channel x 2
Input impedance: 100kΩ
Conditions : Pre-Owned, Mint
Price : Rp 19.000.000,-
Integrated Amplifier

MYRYAD MXI 2080
Product Specs :
Power Output (RMS) 8 ohm : 80w, 4 ohm : 120w
THD at rated power 80% rated power, 8 ohms, 20Hz - 20kHz:...
Frequency Response (20Hz - 20kHz) +/-0.2dB (-2dB @ 96kHz)...
Signal/Noise ratio (A-weighted, ref 80W): >107dB
Input Selector Line Direct, Tape, CD-R, CD, Tuner, TV...
Dimensions (HxWxD) mm95 x 436 x 355mm
Input Sensitivity 320mV (user trimmable 160-640mV)
Input impedance 22k/200pf
Fascia 9mm anodised bead blasted aluminium in...
Weight 11.0 kg
Condition : Pre-Owned, Mint
Price : Rp 12.000.000,-
Product Specs :
Power Output (RMS) 8 ohm : 80w, 4 ohm : 120w
THD at rated power 80% rated power, 8 ohms, 20Hz - 20kHz:...
Frequency Response (20Hz - 20kHz) +/-0.2dB (-2dB @ 96kHz)...
Signal/Noise ratio (A-weighted, ref 80W): >107dB
Input Selector Line Direct, Tape, CD-R, CD, Tuner, TV...
Dimensions (HxWxD) mm95 x 436 x 355mm
Input Sensitivity 320mV (user trimmable 160-640mV)
Input impedance 22k/200pf
Fascia 9mm anodised bead blasted aluminium in...
Weight 11.0 kg
Condition : Pre-Owned, Mint
Price : Rp 12.000.000,-
Integrated Amplifier (Hybrid)

UNICO P
MADE IN ITALY
The nominally 50W Unico is equipped with four line-level inputs, one tape loop, dual speaker terminals, and a phono stage. It's a mark of quality that the input selector switch is right at the back of the circuit board, as close as possible to the RCA inputs to minimise signal-path length. The switch is driven by a long shaft from the rear of the control knob on the fascia. The mains transformer is handmade by Unison Research to an original design, and makes a notable contribution to the weight of the amp.
The input stage is a pure triode design, featuring a single tried-and-true 12AU7/ ECC82 valve, whereas two are deployed in the Unico. The output stage is based on MOSFETs operating in Class A. These are attached to big chunky heatsinks together weighing over a kilo! W ith a stated frequency response of 2-100kHz, the Unico has no fear of new wide-bandwidth formats like SACD and DVD-A.
The internal phono board accomodates both MC (40-50dB) and MM (50-60dB) cartridges - gain and impedance are trimmed by positioning jumper links on the board inside the amp.
Output Power: > 50 watts per channel
Output Impedance: 2 to 8 Ohm
Bandwidth: 2 Hz - 100 kHz at -0.5 dB
Input Impedance: 50 kOhm / 47 pF
Input stage: 1 x twin triode ECC82
Output stage: symmetrical complementary power MOSFETs
Damping factor: >60
Feedback factor: 14 dB
Power consumption: max 250 watt
Dimensions (w x d x h): 435 x 340 x h.95 mm
Nett weight: about 12 kg
-------SOLD-------
MADE IN ITALY
The nominally 50W Unico is equipped with four line-level inputs, one tape loop, dual speaker terminals, and a phono stage. It's a mark of quality that the input selector switch is right at the back of the circuit board, as close as possible to the RCA inputs to minimise signal-path length. The switch is driven by a long shaft from the rear of the control knob on the fascia. The mains transformer is handmade by Unison Research to an original design, and makes a notable contribution to the weight of the amp.
The input stage is a pure triode design, featuring a single tried-and-true 12AU7/ ECC82 valve, whereas two are deployed in the Unico. The output stage is based on MOSFETs operating in Class A. These are attached to big chunky heatsinks together weighing over a kilo! W ith a stated frequency response of 2-100kHz, the Unico has no fear of new wide-bandwidth formats like SACD and DVD-A.
The internal phono board accomodates both MC (40-50dB) and MM (50-60dB) cartridges - gain and impedance are trimmed by positioning jumper links on the board inside the amp.
Output Power: > 50 watts per channel
Output Impedance: 2 to 8 Ohm
Bandwidth: 2 Hz - 100 kHz at -0.5 dB
Input Impedance: 50 kOhm / 47 pF
Input stage: 1 x twin triode ECC82
Output stage: symmetrical complementary power MOSFETs
Damping factor: >60
Feedback factor: 14 dB
Power consumption: max 250 watt
Dimensions (w x d x h): 435 x 340 x h.95 mm
Nett weight: about 12 kg
-------SOLD-------
Integrated Amplifier

AYRE AX7e
MADE IN USA
The Ayre AX-7e integrated amplifier combines sophisticated control functions with a dynamic output section in a single sleek chassis. But don't let its compact size fool you—it delivers all of music’s drama and excitement, employing the same exclusive zero-feedback design found in our reference products. Extremely flexible, the AX-7e offers true balanced inputs and full remote control capabilities. Its custom-designed volume control features FET switches and precision metal-film resistors to ensure total purity of sound. The Ayre AX-7e removes the last veil between you and music’s magic.
Specifications :
Power Output :
60 watts per channel continuous into 8 ohms
120 watts per channel continuous into 4 ohms
Frequency Response :
2Hz - 200 kHz
Input Impedance :
20 Kohm (per phase)
Power Consumption
20 watts in standby mode
70 watts in operating mode, no signal
Dimensions :
17.25" W x 13.75" D x 4.75" H
(43.8cm x 35cm x 12cm)
Weight :
26 pounds (12 kg)
------SOLD--------
MADE IN USA
The Ayre AX-7e integrated amplifier combines sophisticated control functions with a dynamic output section in a single sleek chassis. But don't let its compact size fool you—it delivers all of music’s drama and excitement, employing the same exclusive zero-feedback design found in our reference products. Extremely flexible, the AX-7e offers true balanced inputs and full remote control capabilities. Its custom-designed volume control features FET switches and precision metal-film resistors to ensure total purity of sound. The Ayre AX-7e removes the last veil between you and music’s magic.
Specifications :
Power Output :
60 watts per channel continuous into 8 ohms
120 watts per channel continuous into 4 ohms
Frequency Response :
2Hz - 200 kHz
Input Impedance :
20 Kohm (per phase)
Power Consumption
20 watts in standby mode
70 watts in operating mode, no signal
Dimensions :
17.25" W x 13.75" D x 4.75" H
(43.8cm x 35cm x 12cm)
Weight :
26 pounds (12 kg)
------SOLD--------
Integrated Amplifier (Tube)

AUDIO INNOVATIONS S500
MADE IN UK
Specifications :
Output power : 25W, class A, 30Hz-20kHz +/-3dB
Input sensitivity (excluding phono) : 400mV (max. signal voltage 3V)
Channel separation : > 78dB
Input impedance : 100KOhms
RIAA equalizing accuracy (phono input) : < 0,1dB in the frequency range 20Hz - 20kHz
Total harmonic distortion (THD) : <0,15% in the frequency range 80Hz-15kHz/1W
Inputs : Phono, Tuner, CD, Aux, Tape, Monitor
Negative feedback (NFB) depth : 14dB
Power consumption : 230W
Weight : 17kg
Tubes : 3xECC83, 2xECC88, 4xEL34
-----SOLD------
MADE IN UK
Specifications :
Output power : 25W, class A, 30Hz-20kHz +/-3dB
Input sensitivity (excluding phono) : 400mV (max. signal voltage 3V)
Channel separation : > 78dB
Input impedance : 100KOhms
RIAA equalizing accuracy (phono input) : < 0,1dB in the frequency range 20Hz - 20kHz
Total harmonic distortion (THD) : <0,15% in the frequency range 80Hz-15kHz/1W
Inputs : Phono, Tuner, CD, Aux, Tape, Monitor
Negative feedback (NFB) depth : 14dB
Power consumption : 230W
Weight : 17kg
Tubes : 3xECC83, 2xECC88, 4xEL34
-----SOLD------
Integrated Amplifier

CREEK DESTINY
MADE IN UK
Specifications :
Power in to 8 Ohm both channel driven >100W
Power in to 4 Ohm one channel driven > 180W
Max Current > 25amps
THD < 0.02% 20Hz - 20Khz
Frequency Response 1Hz - 30Khz - 1dB
Slew Rate > 50 V per µS
Gain with, passive pre-amp x48 or 33.6db
Gain increase with active pre-amp +3db +6db +9db
Input Sensitivity 589mv for 100W
Separation > 60dB
Signal to Noise > 78dB
Remote Yes (SRC 2 )
Inputs 5 line inputs + 1 tape loop
Outputs 4
Headphone output Yes
A/B speaker switch Yes
Switchable pre-amp output & power amp input Yes, on the rear of amp
Voltage Switchable 115V / 230V
Power Consumption 400W - <1W in standby
Weight 10Kg
Size W/H/D 430 x 70 x 310mm
------SOLD-------
MADE IN UK
Specifications :
Power in to 8 Ohm both channel driven >100W
Power in to 4 Ohm one channel driven > 180W
Max Current > 25amps
THD < 0.02% 20Hz - 20Khz
Frequency Response 1Hz - 30Khz - 1dB
Slew Rate > 50 V per µS
Gain with, passive pre-amp x48 or 33.6db
Gain increase with active pre-amp +3db +6db +9db
Input Sensitivity 589mv for 100W
Separation > 60dB
Signal to Noise > 78dB
Remote Yes (SRC 2 )
Inputs 5 line inputs + 1 tape loop
Outputs 4
Headphone output Yes
A/B speaker switch Yes
Switchable pre-amp output & power amp input Yes, on the rear of amp
Voltage Switchable 115V / 230V
Power Consumption 400W - <1W in standby
Weight 10Kg
Size W/H/D 430 x 70 x 310mm
------SOLD-------
Integrated Amplifier (Tube)

ANTHEM
BY SONIC FRONTIERS
MADE IN CANADA
INTEGRATED AMPLIFIER SPECIFICATIONS
RATED POWER: 25 Watts continuous: 10Vrms into 4 ohms or 14.14 Vrms into 8 ohms both channels driven 30Hz to 15kHz @ <1% THD&N; (user selectable 4 and 8 ohms taps on rear panel)
FREQUENCY RESPONSE: -0.5dB 30Hz to 25kHz (@ rated power); -3.0dB 10Hz to 65kHz (@ rated power)
SIGNAL TO NOISE RATIO : £ -83dB (A weighted ref 25W rated power); £ -72dB (Unweighted ref 25W rated power)
T H D & N : £ 0.2% 1kHz @ rated power, £ 1% 30Hz to 15kHz @ rated power, £ 3% 18Hz to 23kHz @ rated power
P H A S E : Polarity Inverting
INPUT IMPEDANCE: 750k ohms (Line level inputs)
GAIN: +40dB
SENSITIVITY: 160mV input for rated power (Volume control @ maximum)
PRE AMPLIFIER SPECIFICATIONS
Line Level Inputs to Pre Outputs
INPUT IMPEDANCE: 750k ohms (line level inputs)
OUTPUT IMPEDANCE: 7k ohms (minimum required load: 100k ohms)
FREQUENCY RESPONSE: -0.5dB 30Hz to 20kHz, -3.0dB 10Hz to 55kHz
SIGNAL TO NOISE RATIO: £ -75dB (Unweighted ref 1V @ Pre Out); £ -85dB (A weighted ref 1V @ Pre Out)
THD&N: £0.3% 10Hz to 50kHz (Ref 1V @ Pre Out)
P H A S E : Polarity Inverting
GAIN: +12dB
POWER AMPLIFIER SPECIFICATIONS
Power Amplifier Inputs to Main Speaker Outputs
RATED POWER: 25 Watts continuous into 4 or 8 ohms both channels driven 30Hz to 15kHz @ <1% THD&N; (user selectable 4 and 8 Ohm taps on rear panel)
FREQUENCY RESPONSE: -0.5dB 10Hz to 40kHz (1W); -3.0dB 15Hz to 150kHz (1W); -0.5db 10Hz to 40kHz (@ rated power); -3dB 15 Hz to 100kHz (@ rated power)
SIGNAL TO NOISE RATIO: £ -95dB (A weighted ref 25W rated power); £ -87dB (Unweighted ref 25W rated power)
THD&N: £1% 30Hz to 15kHz @ rated power; £3% 18Hz to 23kHz @ rated power
P H A S E : Polarity Non-inverting
INPUT IMPEDANCE: 100k ohms (Power Amplifier Inputs)
DAMPING FACTOR : ³8 @ 8 ohms; ³6 @ 4 ohms
GAIN: +28dB
SENSITIVITY: 660mV Input for rated power
All tests were performed with the Audio Precision System One.
------SOLD------
BY SONIC FRONTIERS
MADE IN CANADA
INTEGRATED AMPLIFIER SPECIFICATIONS
RATED POWER: 25 Watts continuous: 10Vrms into 4 ohms or 14.14 Vrms into 8 ohms both channels driven 30Hz to 15kHz @ <1% THD&N; (user selectable 4 and 8 ohms taps on rear panel)
FREQUENCY RESPONSE: -0.5dB 30Hz to 25kHz (@ rated power); -3.0dB 10Hz to 65kHz (@ rated power)
SIGNAL TO NOISE RATIO : £ -83dB (A weighted ref 25W rated power); £ -72dB (Unweighted ref 25W rated power)
T H D & N : £ 0.2% 1kHz @ rated power, £ 1% 30Hz to 15kHz @ rated power, £ 3% 18Hz to 23kHz @ rated power
P H A S E : Polarity Inverting
INPUT IMPEDANCE: 750k ohms (Line level inputs)
GAIN: +40dB
SENSITIVITY: 160mV input for rated power (Volume control @ maximum)
PRE AMPLIFIER SPECIFICATIONS
Line Level Inputs to Pre Outputs
INPUT IMPEDANCE: 750k ohms (line level inputs)
OUTPUT IMPEDANCE: 7k ohms (minimum required load: 100k ohms)
FREQUENCY RESPONSE: -0.5dB 30Hz to 20kHz, -3.0dB 10Hz to 55kHz
SIGNAL TO NOISE RATIO: £ -75dB (Unweighted ref 1V @ Pre Out); £ -85dB (A weighted ref 1V @ Pre Out)
THD&N: £0.3% 10Hz to 50kHz (Ref 1V @ Pre Out)
P H A S E : Polarity Inverting
GAIN: +12dB
POWER AMPLIFIER SPECIFICATIONS
Power Amplifier Inputs to Main Speaker Outputs
RATED POWER: 25 Watts continuous into 4 or 8 ohms both channels driven 30Hz to 15kHz @ <1% THD&N; (user selectable 4 and 8 Ohm taps on rear panel)
FREQUENCY RESPONSE: -0.5dB 10Hz to 40kHz (1W); -3.0dB 15Hz to 150kHz (1W); -0.5db 10Hz to 40kHz (@ rated power); -3dB 15 Hz to 100kHz (@ rated power)
SIGNAL TO NOISE RATIO: £ -95dB (A weighted ref 25W rated power); £ -87dB (Unweighted ref 25W rated power)
THD&N: £1% 30Hz to 15kHz @ rated power; £3% 18Hz to 23kHz @ rated power
P H A S E : Polarity Non-inverting
INPUT IMPEDANCE: 100k ohms (Power Amplifier Inputs)
DAMPING FACTOR : ³8 @ 8 ohms; ³6 @ 4 ohms
GAIN: +28dB
SENSITIVITY: 660mV Input for rated power
All tests were performed with the Audio Precision System One.
------SOLD------
Integrated Amplifier

ROKSAN KANDY MKIII
MADE IN UK
Description: Equipped with six inputs and a separate tape input, accommodating seven source components - one of which can be switched to work as a moving magnet or moving coil phono-stage. 120 Watts per channel power output, the amplifier can partner a wide range of loudspeakers. Headphone output mounted on the near panel.
------SOLD-----
MADE IN UK
Description: Equipped with six inputs and a separate tape input, accommodating seven source components - one of which can be switched to work as a moving magnet or moving coil phono-stage. 120 Watts per channel power output, the amplifier can partner a wide range of loudspeakers. Headphone output mounted on the near panel.
------SOLD-----
Integrated Amplifier

AUDIO ANALOGUE
PUCCINI
MADE IN ITALY
The Puccini is a 40 watts integrated amplifier designed with an ultraminimalist approach in mind (just volume and input selector), entirely developed and built in Italy.
Audio Analogue is a new Italian firm which is earning popularity among audiophiles because of its products (some amplifiers + a D/A converter, coming soon a CD player), designed to have a very high value/price ratio.
The amplifier I'm going to listen to has been successfully reviewed by several Italian *paper* mags and this has raised my interest even more.
-----SOLD-----
PUCCINI
MADE IN ITALY
The Puccini is a 40 watts integrated amplifier designed with an ultraminimalist approach in mind (just volume and input selector), entirely developed and built in Italy.
Audio Analogue is a new Italian firm which is earning popularity among audiophiles because of its products (some amplifiers + a D/A converter, coming soon a CD player), designed to have a very high value/price ratio.
The amplifier I'm going to listen to has been successfully reviewed by several Italian *paper* mags and this has raised my interest even more.
-----SOLD-----
Integrated Amplifier

KRELL S-300i
MADE IN USA
Power Output:150Wpc into 8 ohms, 300Wpc into 4 ohms
Inputs:Three RCA, one XLR (all line inputs)
Dimensions:17.25” x 4.20” x 17.50”
Weight:43 lbs.
-----SOLD------
MADE IN USA
Power Output:150Wpc into 8 ohms, 300Wpc into 4 ohms
Inputs:Three RCA, one XLR (all line inputs)
Dimensions:17.25” x 4.20” x 17.50”
Weight:43 lbs.
-----SOLD------
Integrated Amplifier (Tube)

ROGERS E20A
MADE IN UK
SPECIFICATIONS :
Designed and built for digital era, the Rogers E-20a Class 'A' Stereo Integrated Amplifiers truly represent digital sound the way it should be heard and appreciated.These superb fully integrated, all-valve, handmade amplifiers are guaranteed to send tingles down the spine of the most discerning of audio aficionado's. Recommended for use with a wide range of the highest quality transducer or electrostatic speakers.
Power : 20 watts per channel class 'A'
Valve Output : Push Pull Cathode Follower
Self Bias 6L6GT x 4
Phono Stage : 2 x ECC83/12AX7
Line Input Impedance : Phono: 47K ohms, Line: 100K ohms
------SOLD------
MADE IN UK
SPECIFICATIONS :
Designed and built for digital era, the Rogers E-20a Class 'A' Stereo Integrated Amplifiers truly represent digital sound the way it should be heard and appreciated.These superb fully integrated, all-valve, handmade amplifiers are guaranteed to send tingles down the spine of the most discerning of audio aficionado's. Recommended for use with a wide range of the highest quality transducer or electrostatic speakers.
Power : 20 watts per channel class 'A'
Valve Output : Push Pull Cathode Follower
Self Bias 6L6GT x 4
Phono Stage : 2 x ECC83/12AX7
Line Input Impedance : Phono: 47K ohms, Line: 100K ohms
------SOLD------
Integrated Amplifier (Tube)

PRIMALUNA PROLOGUE ONE
MADE IN CHINA
Description: Single-box line-level tube preamplifier and push-pull tube power amplifier. Tube complement: two each 12AX7A, 12AU7, EL34. Inputs: 4 single-ended. Output power: 35Wpc into 8 ohms (15.4dBW). Voltage gain: 20dB. Output impedance: 4 or 8 ohms. Frequency response: 20Hz–30kHz, ±0.5dB. Input impedance: 100k ohms. Input sensitivity: 300mV.Dimensions: 11.5" W by 7.7" H by 15" D. Weight: 36 lbs
----SOLD-----
MADE IN CHINA
Description: Single-box line-level tube preamplifier and push-pull tube power amplifier. Tube complement: two each 12AX7A, 12AU7, EL34. Inputs: 4 single-ended. Output power: 35Wpc into 8 ohms (15.4dBW). Voltage gain: 20dB. Output impedance: 4 or 8 ohms. Frequency response: 20Hz–30kHz, ±0.5dB. Input impedance: 100k ohms. Input sensitivity: 300mV.Dimensions: 11.5" W by 7.7" H by 15" D. Weight: 36 lbs
----SOLD-----
Integrated Amplifier

BLUENOTE DEMIDOFF
MADE IN ITALY
Solid state Integrated amp 75 watt / channel
----SOLD-------
MADE IN ITALY
Solid state Integrated amp 75 watt / channel
----SOLD-------
Integrated Amplifier

PLINIUS 9100
MADE IN NEW ZEALAND
Specifications :
Power: 120 watts per channel into 8 Ohms
Both channels driven from 20Hz to
at less than 0.2% total harmonic distortion
Frequency Response: 20Hz to 20kHz +/–0.2dB
–3dB at 5Hz and –3dB at 70kHz
Distortion: Typically <0.05% THD at rated power
0.2% THD and IM worst case prior to clipping
Current Output: 20A short duration peak per channel , fuse protected
Slewing: 50V/μs.
Hum & Noise: 90dB below rated ouput 20Hz to
20kHz unweighted
Gain: Line inputs to speaker out: 40dB
Input Impedance: 47kOhms all inputs
Input Overload: 5V RMS
Rated Pre Out Level: 1.5V RMS into 47kOhms or higher
Pre Out Source Impedance: Typically 1.5k Ohms
Pre Out Minimum
Recommended Load: 47k Ohms
Tape Output Level: 190mV at 200 Ohms
Tape loop muting at 5V RMS input
Dimensions: Height: 105mm (4”)
Width: 450mm (17 3/4”)
Depth: 400mm (15 3/4”)
Weight: 10kg (22lbs)
------SOLD-------
MADE IN NEW ZEALAND
Specifications :
Power: 120 watts per channel into 8 Ohms
Both channels driven from 20Hz to
at less than 0.2% total harmonic distortion
Frequency Response: 20Hz to 20kHz +/–0.2dB
–3dB at 5Hz and –3dB at 70kHz
Distortion: Typically <0.05% THD at rated power
0.2% THD and IM worst case prior to clipping
Current Output: 20A short duration peak per channel , fuse protected
Slewing: 50V/μs.
Hum & Noise: 90dB below rated ouput 20Hz to
20kHz unweighted
Gain: Line inputs to speaker out: 40dB
Input Impedance: 47kOhms all inputs
Input Overload: 5V RMS
Rated Pre Out Level: 1.5V RMS into 47kOhms or higher
Pre Out Source Impedance: Typically 1.5k Ohms
Pre Out Minimum
Recommended Load: 47k Ohms
Tape Output Level: 190mV at 200 Ohms
Tape loop muting at 5V RMS input
Dimensions: Height: 105mm (4”)
Width: 450mm (17 3/4”)
Depth: 400mm (15 3/4”)
Weight: 10kg (22lbs)
------SOLD-------

VTL IT-85
MADE IN USA
SPECIFICATIONS :
Vacuum Tube Complement : 4 x EL34, 4 x 12AT7, 2 x 12AU7
Output power : 60 Watts
20Hz – 20KHz <3% THD Into 5Ω
Small signal frequency response : (<0.2% THD @ 1W), 0-60 kHz
Class of operation : Class AB1
Inputs : 5 pairs of single-ended RCA, Proc/Amp Input
Outputs : 1 pair 5-way binding posts, Pre Out, Tape Out, Headphone Out
Input sensitivity : Line in: 180mV, Amp in: 575mV
Input impedance : Line in: 20kΩ, Amp in: 135kΩ
Output impedance : Amp out: 1.55Ω, Headphone out: 16Ω, Preamp out: 400Ω
Load setting : Speakers: 5Ω, Headphones: 50-500Ω
Power consuption : Ide = 200W, Full Power=600W
Dimensions W x D x H : 15.75 x 11 x 7 inches, 40 x 28 x 17.75 cm
Weight : 55lbs (29.5Kg) fully packed
-----SOLD------
MADE IN USA
SPECIFICATIONS :
Vacuum Tube Complement : 4 x EL34, 4 x 12AT7, 2 x 12AU7
Output power : 60 Watts
20Hz – 20KHz <3% THD Into 5Ω
Small signal frequency response : (<0.2% THD @ 1W), 0-60 kHz
Class of operation : Class AB1
Inputs : 5 pairs of single-ended RCA, Proc/Amp Input
Outputs : 1 pair 5-way binding posts, Pre Out, Tape Out, Headphone Out
Input sensitivity : Line in: 180mV, Amp in: 575mV
Input impedance : Line in: 20kΩ, Amp in: 135kΩ
Output impedance : Amp out: 1.55Ω, Headphone out: 16Ω, Preamp out: 400Ω
Load setting : Speakers: 5Ω, Headphones: 50-500Ω
Power consuption : Ide = 200W, Full Power=600W
Dimensions W x D x H : 15.75 x 11 x 7 inches, 40 x 28 x 17.75 cm
Weight : 55lbs (29.5Kg) fully packed
-----SOLD------
Integrated Amplifier

BADA PURER 3.3
MADE IN CHINA
GENERAL FEATURES:
Heavy duty chassis constructed of aluminum pieces
Inner partitions design prohibits interference
Symmetrical dual mono desgn
1 x R-core transformer for pre-amplification session
2 x 380W toroidal power transformer for power amplification stage
Low loss relay employed for input exchange
Vacuum tube pre-amplification stage
Fully balanced direct AC power amplification stage
6N11 (6922) vacuum tubes in pre-amplfier session
8 pairs of high current output transistors in power amplifier session
Imported ALPS volume control
2 adjustable pure Class A power output selection: 10W / 30W
3 adjustable preset timbre in pre-amplifier session
Bypass function for original sonic amplification
Solen coupling capacitors and Wima MKP10 capacitors
Very strong bass control, full dynamics with musical presentation
Infrared full remote control
Gold plated speaker output posts
RCA and XLR balanced inputs
Detachable power cord system (IEC)
TECHNICAL DATA:
FREQUENCY RESPONSE: 5Hz – 80Khz (-3db), Bypass mode
OUTPUT POWER: Pure Class A 2 x 10W (8ohms), A1 selection
Pure Class A 2 x 30W (8ohms), A2 selection
Class AB: 2 x 160W (8ohms)
VACUUM TUBES: 6N11 (6922) x 2
THD + N: <0.05%
S/N RATIO: >95db (A weighed)
-----SOLD-----
MADE IN CHINA
GENERAL FEATURES:
Heavy duty chassis constructed of aluminum pieces
Inner partitions design prohibits interference
Symmetrical dual mono desgn
1 x R-core transformer for pre-amplification session
2 x 380W toroidal power transformer for power amplification stage
Low loss relay employed for input exchange
Vacuum tube pre-amplification stage
Fully balanced direct AC power amplification stage
6N11 (6922) vacuum tubes in pre-amplfier session
8 pairs of high current output transistors in power amplifier session
Imported ALPS volume control
2 adjustable pure Class A power output selection: 10W / 30W
3 adjustable preset timbre in pre-amplifier session
Bypass function for original sonic amplification
Solen coupling capacitors and Wima MKP10 capacitors
Very strong bass control, full dynamics with musical presentation
Infrared full remote control
Gold plated speaker output posts
RCA and XLR balanced inputs
Detachable power cord system (IEC)
TECHNICAL DATA:
FREQUENCY RESPONSE: 5Hz – 80Khz (-3db), Bypass mode
OUTPUT POWER: Pure Class A 2 x 10W (8ohms), A1 selection
Pure Class A 2 x 30W (8ohms), A2 selection
Class AB: 2 x 160W (8ohms)
VACUUM TUBES: 6N11 (6922) x 2
THD + N: <0.05%
S/N RATIO: >95db (A weighed)
-----SOLD-----
Integrated Amplifier (Tube)

WAVAC MD-811
MADE IN JAPAN
Specifications:
Effective Power output: 15 watts per channel
Frequency range: 20Hz-50KHz
Input sensitivity: 2.0Vrms
Input impedance: 100k ohms
S/N ratio: 72dB
Power consumption: 260 watts
Power supply: 117V(100V/230V/240V) AC 50-60Hz
Load impedance: 8(4/16) ohms
External dimensions: 265W x 420D x 200H(mm)
Weight: 17kg (37.4 pounds)
------SOLD-------
MADE IN JAPAN
Specifications:
Effective Power output: 15 watts per channel
Frequency range: 20Hz-50KHz
Input sensitivity: 2.0Vrms
Input impedance: 100k ohms
S/N ratio: 72dB
Power consumption: 260 watts
Power supply: 117V(100V/230V/240V) AC 50-60Hz
Load impedance: 8(4/16) ohms
External dimensions: 265W x 420D x 200H(mm)
Weight: 17kg (37.4 pounds)
------SOLD-------

MARK LEVINSON NO.383
MADE IN USA
Description: Solid-state integrated stereo amplifier.
Preamplifier section: Line-level inputs: two pairs balanced (XLR), three pairs single-ended (RCA, optional). Outputs: one pair record outputs (RCA), one IEC AC mains receptacle, one ground terminal. Controller connections: three 3.5mm mini-jacks (IR input, DC trigger out/in), one Mark Levinson Link communications connector, one 6-pin RJ-11 RS-232 port, two 8-pin RJ-45 control ports (PHASTLink-compatible). Voltage gain: 0, 6, 12, or 18dB in line stage (26.9dB in amplifier stage). Volume control range: 72.2dB. Gain resolution: 0.1dB steps above 38.5 in display (-34.7dB). Input overload: 4V on XLR, 2V on RCA (gain set to +12dB); 16V on XLR, 8V on RCA (gain set to 0dB). Frequency response: 10Hz-40kHz, ±1.0dB. Input impedance: 100k ohms. THD+noise: ±0.3%. Mains voltage: 100V, 120V, 220V, 230V, or 240VAC at 50 or 60Hz (factory set). Power consumption: typically 100W at standby, 200W at idle, 1200W at 4 ohms at rated output.
Amplifier section: Rated output power: 20Hz-20kHz, less than 0.3% THD (FTC): 100Wpc into 8 ohms (20dBW), 200W minimum continuous into 4 ohms (20dBW). Frequency response: 20Hz-20kHz, ±0.1dB. Output impedance: ±0.05 ohms, 20Hz-20kHz. Damping factor: greater than 800, 20Hz-20kHz into 8 ohms. Speaker connections: one pair Madrigal-designed speaker binding posts.
Dimensions: 17.56" (446mm) W by 6.55" (166mm) H by 19.5" (495.3mm) D. Shipping weight: 80 lbs (36.6kg).
-----SOLD------
MADE IN USA
Description: Solid-state integrated stereo amplifier.
Preamplifier section: Line-level inputs: two pairs balanced (XLR), three pairs single-ended (RCA, optional). Outputs: one pair record outputs (RCA), one IEC AC mains receptacle, one ground terminal. Controller connections: three 3.5mm mini-jacks (IR input, DC trigger out/in), one Mark Levinson Link communications connector, one 6-pin RJ-11 RS-232 port, two 8-pin RJ-45 control ports (PHASTLink-compatible). Voltage gain: 0, 6, 12, or 18dB in line stage (26.9dB in amplifier stage). Volume control range: 72.2dB. Gain resolution: 0.1dB steps above 38.5 in display (-34.7dB). Input overload: 4V on XLR, 2V on RCA (gain set to +12dB); 16V on XLR, 8V on RCA (gain set to 0dB). Frequency response: 10Hz-40kHz, ±1.0dB. Input impedance: 100k ohms. THD+noise: ±0.3%. Mains voltage: 100V, 120V, 220V, 230V, or 240VAC at 50 or 60Hz (factory set). Power consumption: typically 100W at standby, 200W at idle, 1200W at 4 ohms at rated output.
Amplifier section: Rated output power: 20Hz-20kHz, less than 0.3% THD (FTC): 100Wpc into 8 ohms (20dBW), 200W minimum continuous into 4 ohms (20dBW). Frequency response: 20Hz-20kHz, ±0.1dB. Output impedance: ±0.05 ohms, 20Hz-20kHz. Damping factor: greater than 800, 20Hz-20kHz into 8 ohms. Speaker connections: one pair Madrigal-designed speaker binding posts.
Dimensions: 17.56" (446mm) W by 6.55" (166mm) H by 19.5" (495.3mm) D. Shipping weight: 80 lbs (36.6kg).
-----SOLD------
Integrated Amplifier (Tube)

PRIMALUNA PROLOGUE TWO
DESIGNED IN HOLLAND & MADE IN CHINA
Specifications :
Output : 40 watt x 2
Freq. Response: 20Hz-30kHz +/- .5dB
THD: Less than 1 percent at full power
S/N Ratio: 89 db
Input Sensitivity: 300mV
Power Consumption: 300 watts
Dimensions: 11 " x 7.5 " x 15.5" (WxHxD)Weight: 37.5 lbs
Inputs: 4 pair RCA
Outputs: 4 and 8 Ohm speaker taps
Tube Compliment: 2 - 12AX7, 2 - 12AU7, 4 - KT88
------SOLD-------
DESIGNED IN HOLLAND & MADE IN CHINA
Specifications :
Output : 40 watt x 2
Freq. Response: 20Hz-30kHz +/- .5dB
THD: Less than 1 percent at full power
S/N Ratio: 89 db
Input Sensitivity: 300mV
Power Consumption: 300 watts
Dimensions: 11 " x 7.5 " x 15.5" (WxHxD)Weight: 37.5 lbs
Inputs: 4 pair RCA
Outputs: 4 and 8 Ohm speaker taps
Tube Compliment: 2 - 12AX7, 2 - 12AU7, 4 - KT88
------SOLD-------
Integrated Amplifier (Tube)

SYNTHESIS NIMIS LE
MADE IN ITALY
Technical quality :
Power : 2 X 20W
Fréquency : 20Hz~20KHz±0.5dB
Input impedance : 50 K ohms
Noise ratio : 90 dB
Input : 4 Input line level: Cd player, Tuner, Video, Aux.
other input/output : Tape Out
Power tubes : 4 x EL 84
Préamp and driver tubes : 4 x 12AX7/ECC83
Other informations : Limited edition only 500 pcs with number
-----SOLD-----
MADE IN ITALY
Technical quality :
Power : 2 X 20W
Fréquency : 20Hz~20KHz±0.5dB
Input impedance : 50 K ohms
Noise ratio : 90 dB
Input : 4 Input line level: Cd player, Tuner, Video, Aux.
other input/output : Tape Out
Power tubes : 4 x EL 84
Préamp and driver tubes : 4 x 12AX7/ECC83
Other informations : Limited edition only 500 pcs with number
-----SOLD-----
Integrated Amplifier (Tube)

MANLEY STINGRAY
MADE IN USA
SPECIFICATIONS :
-----SOLD-----
MADE IN USA
SPECIFICATIONS :
- Vacuum Tube Integrated Amplifier
- Power: 40w x 2 (U/L mode) / 20w x 2 (Triode mode)
- Passive Noble volume and balance pots
- All vacuum tube lo-feedback stereo integrated design
- Frequency Response: 15Hz – 40KHz
- Output Tubes: 8 x EL84
- Driver Tubes: 2 x 6414
- Input Tubes: 2 x 12AT7EH
- 4 x RCA audio inputs
- Banana plug compatible speaker binding posts
- Dimensions
- Amp W 19”, x H 5 1/2”, x D 14”
- Weight 30 1bs
-----SOLD-----
Set System (Power Amp & Pre Amp)

DENSEN B-330 & B-200
MADE IN DENMARK
DENSEN B-330
Power output in 8 ohms: 2 x 120W
Power output in 4 ohms: 2 x 240W
Power supply size: 750VA
Storage capacity: 110.000uF
THD + Noise @ rated output: Less than 0.1%
The B-330 is a direct descendent from the top of the line B-350 monoblocks. The B-350 monoblocks act as the internal reference at Densen. Basically, the B-330 is a stereo power amp based on the B-350's technology, and uses the distinct monoblock cabinet with its recessed heatsinks as the basis for an extremely affordable reference power amplifier. The B-330 contains several exciting features. Externally on the backpanel there is a switch to adjust the gain, so it either works perfect with a traditional preamp or with a CD with variable output. There is also a D-Sub15 connector, allowing for Link connection to other Densen products, and for auto power on/off. The D-Sub connector can be daisy-chained in multiroom systems. The B-330 is also prepared for the SAXO electronic crossover. This is done by mounting the crossover internally in the B-330 in a socket. The SAXO crossover will fit all passive speakers on the market.
DATA
Power output in 8 ohms: 2 x 120W
Power output in 4 ohms: 2 x 240W
Power supply size: 750VA
Storage capacity: 110.000uF
THD + Noise @ rated output: Less than 0.1%
Weight/shippingweight: 15/17 Kg
Product dimensions (WxDxH): 440x310x64mm
DENSEN B-200
DATA
Line- & tape inputs: 4 & 2
Preouts: 4
Powersupply size: 2x20VA
Storagecapacity: 25.000uF
THD + Noise @ rated output: Less than 0.05%
Frequency response (+0 -3db): 2-500.000Hz
Weight/shippingweight: 8/10 Kg
Product dimensions (WxDxH): 440x310x64mm
-----SOLD----
MADE IN DENMARK
DENSEN B-330
Power output in 8 ohms: 2 x 120W
Power output in 4 ohms: 2 x 240W
Power supply size: 750VA
Storage capacity: 110.000uF
THD + Noise @ rated output: Less than 0.1%
The B-330 is a direct descendent from the top of the line B-350 monoblocks. The B-350 monoblocks act as the internal reference at Densen. Basically, the B-330 is a stereo power amp based on the B-350's technology, and uses the distinct monoblock cabinet with its recessed heatsinks as the basis for an extremely affordable reference power amplifier. The B-330 contains several exciting features. Externally on the backpanel there is a switch to adjust the gain, so it either works perfect with a traditional preamp or with a CD with variable output. There is also a D-Sub15 connector, allowing for Link connection to other Densen products, and for auto power on/off. The D-Sub connector can be daisy-chained in multiroom systems. The B-330 is also prepared for the SAXO electronic crossover. This is done by mounting the crossover internally in the B-330 in a socket. The SAXO crossover will fit all passive speakers on the market.
DATA
Power output in 8 ohms: 2 x 120W
Power output in 4 ohms: 2 x 240W
Power supply size: 750VA
Storage capacity: 110.000uF
THD + Noise @ rated output: Less than 0.1%
Weight/shippingweight: 15/17 Kg
Product dimensions (WxDxH): 440x310x64mm
DENSEN B-200
DATA
Line- & tape inputs: 4 & 2
Preouts: 4
Powersupply size: 2x20VA
Storagecapacity: 25.000uF
THD + Noise @ rated output: Less than 0.05%
Frequency response (+0 -3db): 2-500.000Hz
Weight/shippingweight: 8/10 Kg
Product dimensions (WxDxH): 440x310x64mm
-----SOLD----
Integrated Amplifier

SPARK 220 Ci
MADE IN CHINA
Specifications :
Transistor Integrated Amplifier 220Ci
POWER OUTPUT:100W+100W(8Ω) PREQUENCY RESPONSE:20Hz~35KHz
THD: 0.2%(1kHz)
INPUT SENSITIVITY:400mV
S/N RATIO: 86dB
DIMENSION: 450×370×105mm WEIGHT:14Kg
POWER CONSUMPTION:300W
----SOLD----
MADE IN CHINA
Specifications :
Transistor Integrated Amplifier 220Ci
POWER OUTPUT:100W+100W(8Ω) PREQUENCY RESPONSE:20Hz~35KHz
THD: 0.2%(1kHz)
INPUT SENSITIVITY:400mV
S/N RATIO: 86dB
DIMENSION: 450×370×105mm WEIGHT:14Kg
POWER CONSUMPTION:300W
----SOLD----
Integrated Amplifier

AUDIO ANALOGUE
PRIMO SETTANTA
MADE IN ITALY
Description:
Primo Settanta is a 70 Watt channels amplifier with line inputs and optional phono stage, high-performance circuits with wide bandwidth and low feedback, separated circuit sections for each channel, linear analogic power supply with a toroidal transformer and five different stabilizing sections, highquality passive components, integrated-resistor network volume controls with no buffer for maximum sound transparency.
----SOLD----
PRIMO SETTANTA
MADE IN ITALY
Description:
Primo Settanta is a 70 Watt channels amplifier with line inputs and optional phono stage, high-performance circuits with wide bandwidth and low feedback, separated circuit sections for each channel, linear analogic power supply with a toroidal transformer and five different stabilizing sections, highquality passive components, integrated-resistor network volume controls with no buffer for maximum sound transparency.
----SOLD----
Integrated Amplifier (Tube Hybrid)

KORA EXPLORER 90 SI
MADE IN FRANCE
The main specifications :
Power output: 60W (8Ohms) 90W (4Ohms)
Bandwidth: 7Hz - 40kHz (-3dB)
Sensitivity: 330mV
Input impedance: 100 kOhms
Dimensions/weight: 420 x 260 x 90mm, 7kg
The main principle behind the Explorer's innards is simplicity. A first gain stage uses one ECC81 double-triode for both channels, and the actual power output stage contains another ECC81 and a mere 4 (MOS)FETs in a circuit that further only makes sparse use of passive components. The output stage employs just 6dB of loop feedback
-----SOLD-----
MADE IN FRANCE
The main specifications :
Power output: 60W (8Ohms) 90W (4Ohms)
Bandwidth: 7Hz - 40kHz (-3dB)
Sensitivity: 330mV
Input impedance: 100 kOhms
Dimensions/weight: 420 x 260 x 90mm, 7kg
The main principle behind the Explorer's innards is simplicity. A first gain stage uses one ECC81 double-triode for both channels, and the actual power output stage contains another ECC81 and a mere 4 (MOS)FETs in a circuit that further only makes sparse use of passive components. The output stage employs just 6dB of loop feedback
-----SOLD-----
Set System (CD Player + Int Amp)

MUSICAL FIDELITY
X-RAY & X-A1
MADE IN UK
Rated at 50 watts per channel into 8 ohms (100W into 4 ohms, 200 into 2) and with a 15-amp peak power capability it has six line-level inputs (labelled CD, Tuner Aux 1, 2 and 3, and Tape), a separate Tape Monitor switch and a preamplifier stage output. There are no tone controls or filters and the amplifier caters for just one pair of loudspeakers via 4mm socket/binding posts. Built into an elongated form of the X-Series tubular case, the X-Al boasts a substantial milled aluminium fascia and is housed in the familiar extruded cabinet. The power supply is a separate unit housed in a plastics case.
-----SOLD---
X-RAY & X-A1
MADE IN UK
Rated at 50 watts per channel into 8 ohms (100W into 4 ohms, 200 into 2) and with a 15-amp peak power capability it has six line-level inputs (labelled CD, Tuner Aux 1, 2 and 3, and Tape), a separate Tape Monitor switch and a preamplifier stage output. There are no tone controls or filters and the amplifier caters for just one pair of loudspeakers via 4mm socket/binding posts. Built into an elongated form of the X-Series tubular case, the X-Al boasts a substantial milled aluminium fascia and is housed in the familiar extruded cabinet. The power supply is a separate unit housed in a plastics case.
-----SOLD---
Integrated Amplifier

MOON i-1 by SIMAUDIO
MADE IN CANADA
Significant Design Features:
-----SOLD---
MADE IN CANADA
Significant Design Features:
- An oversized power supply using a custom toroidal transformer design
- Rated output of 50 watts/channel into 8 ohms and 100 watts/channel into 4 ohms
- 6 line-level inputs including a front-mounted 1/8” mini-jack for personal media players
- Headphone output on ¼” TRS jack located on the front panel
- Remote control operation
- RS-232 port for i) full unsolicited bidirectional feedback in custom installation setupsand ii) firmware updates
- IR input for external control
- SimLink controller port allows for 2-way communications between other compatible MOON components
- Class A output to 5 watts for greater efficiency
- PCB w/ pure copper tracings & gold plating that yields low impedance characteristics
- Optimized selection of very high quality electronic components
- Heat-sink free design incorporating an all-aluminum chassis for evenly distributed heat dissipation
- Rigid chassis construction to minimize the effects of external vibrations
- Designed to be powered up at all times for optimal performance
- Low operating temperature to ensure a longer than normal life expectancy.
-----SOLD---
Integrated Amplifier

CARY AUDIO
CAI 1
Specifications :
Preamplifier Input : 1 pair balanced on XLR
6 pair single-ended on RCA
Input Sensitivity : 1.2 V (full-rated output)
Record Output : 1 pair record output on RCA
Controller Connectors : 1 - IEC AC mains receptacle
1- 3.5mm “mini plug” jack for IR input
3- 3.5mm “mini plug” jack for trigger out
RS 232 full remote configuration interface
Volume Control Range : 63.0 dB
Gain Resolution : 1.0 dB steps
Input Overload : 6 V on XLR, 3 V on RCA
Input Impedance : 100k Ohms on RCA, 200k Ohms on XLR
Output Impedance : 4 - 8 Ohms
Rated Power Output : 125 watts/channel rms. at 8 Ohms
250 watts/channel rms. at 4 Ohms
THD : 0.0005% 10W, 4 Ohms 14kHz/15kHz
THD+N : 0.006% @ 1W, 8 Ohms 1 kHz, <0.2%, 0.1W - 200W, 4 Ohms
Frequency Response : +/- 0.5 dB from 20 Hz to 22 kHz
Signal-to-Noise Ratio : -80 dB CCIR
Voltage Gain : 26.8 dB
Damping Factor : > 4000, 100 Hz 8 Ohms
Power Input : Configured at factory for either 100 to 120 or 200 to 240 VAC, 50-60 Hz
Power Consumption : 400 watts - Full Power
20 watts - Idle
5 watts - Standby
Weight : 23 lbs.
Dimensions 4.5" H x 17" W x 13" D
----SOLD---
CAI 1
Specifications :
Preamplifier Input : 1 pair balanced on XLR
6 pair single-ended on RCA
Input Sensitivity : 1.2 V (full-rated output)
Record Output : 1 pair record output on RCA
Controller Connectors : 1 - IEC AC mains receptacle
1- 3.5mm “mini plug” jack for IR input
3- 3.5mm “mini plug” jack for trigger out
RS 232 full remote configuration interface
Volume Control Range : 63.0 dB
Gain Resolution : 1.0 dB steps
Input Overload : 6 V on XLR, 3 V on RCA
Input Impedance : 100k Ohms on RCA, 200k Ohms on XLR
Output Impedance : 4 - 8 Ohms
Rated Power Output : 125 watts/channel rms. at 8 Ohms
250 watts/channel rms. at 4 Ohms
THD : 0.0005% 10W, 4 Ohms 14kHz/15kHz
THD+N : 0.006% @ 1W, 8 Ohms 1 kHz, <0.2%, 0.1W - 200W, 4 Ohms
Frequency Response : +/- 0.5 dB from 20 Hz to 22 kHz
Signal-to-Noise Ratio : -80 dB CCIR
Voltage Gain : 26.8 dB
Damping Factor : > 4000, 100 Hz 8 Ohms
Power Input : Configured at factory for either 100 to 120 or 200 to 240 VAC, 50-60 Hz
Power Consumption : 400 watts - Full Power
20 watts - Idle
5 watts - Standby
Weight : 23 lbs.
Dimensions 4.5" H x 17" W x 13" D
----SOLD---
Integrated Amplifier

CAMBRIDGE AUDIO AZUR 640A V2
Power Output: 75 watts into 8 Ohms
120 watts into 4 Ohms
Input Impedance: 47k Ohms
Loudspeaker Impedance: 4 to 8 Ohms
Line: 330mV
Phono (using optional phono stage): 1.75mV
Frequency Response: 5Hz to 50kHz +/- 1dB
Bass: +/- 7.5dB @20Hz
Treble: +/- 7.5dB @20kHz
Signal to Noise Ratio (No weighting): 90dB
Slew rate (into 8 ohms): 30V/uS
Max. Power Consumption: 515 Watts
Dimensions (W x D x H): 430 x 310 x 100mm
Weight: 7 kg/15.4 lbs
----SOLD---
Power Output: 75 watts into 8 Ohms
120 watts into 4 Ohms
Input Impedance: 47k Ohms
Loudspeaker Impedance: 4 to 8 Ohms
Line: 330mV
Phono (using optional phono stage): 1.75mV
Frequency Response: 5Hz to 50kHz +/- 1dB
Bass: +/- 7.5dB @20Hz
Treble: +/- 7.5dB @20kHz
Signal to Noise Ratio (No weighting): 90dB
Slew rate (into 8 ohms): 30V/uS
Max. Power Consumption: 515 Watts
Dimensions (W x D x H): 430 x 310 x 100mm
Weight: 7 kg/15.4 lbs
----SOLD---
Integrated Amplifier

BLUENOTE STEROID 1 SIGNATURE MKII
MADE IN ITALY
The Steroid 1 Signature MKII is a Dual Mono Stereo Integrated Amplifier with 5 inputs and 40 watt per channel into 8ohms. It is totally diamagnetic and is hand wired with rectangular solid core OFC bars (RSB). The front panel is made with Polished black Acrylic.
It is hard to describe our super bargain amplifier. This amp is a new, apparently simple way, to realize solid state amp sounding like good (very good) tube amps with twice their power.
Technical details
DIMENSIONS: 430mm L x 90mm H x 350mm D
INPUT/OUTPUT : 5 Line + 1 Phono (optional) + 1 fix output
WEIGHT: Kg. 7,00
FREQUENCY RESPONSE: 1Hz - 25KHz @ +/- 3dB
THD (Total Harmonic Distortion): 0,1% @ 20Hz - 20KHz
PHONO INPUT IMPEDENCE (OPTIONAL): 47 Kohm (47Kohm MM o 470ohm MC)
INPUT SENSIVITY: 550 mV (0,9 to 5,0 mV MM variable acceptance) (0,3 to 0,8 mV MC variable acceptance)
RATIO SIGNAL/NOISE : -90dB
SLEW RATE: 13 Volt Line
POWER OUTPUT: 40w+40w 20-20.000Hz max. 0,2%
THD POWER TRASNFORMERS: 2 AUDIO Power CUSTOM Trafo – 1 Volume control
----SOLD---
MADE IN ITALY
The Steroid 1 Signature MKII is a Dual Mono Stereo Integrated Amplifier with 5 inputs and 40 watt per channel into 8ohms. It is totally diamagnetic and is hand wired with rectangular solid core OFC bars (RSB). The front panel is made with Polished black Acrylic.
It is hard to describe our super bargain amplifier. This amp is a new, apparently simple way, to realize solid state amp sounding like good (very good) tube amps with twice their power.
Technical details
DIMENSIONS: 430mm L x 90mm H x 350mm D
INPUT/OUTPUT : 5 Line + 1 Phono (optional) + 1 fix output
WEIGHT: Kg. 7,00
FREQUENCY RESPONSE: 1Hz - 25KHz @ +/- 3dB
THD (Total Harmonic Distortion): 0,1% @ 20Hz - 20KHz
PHONO INPUT IMPEDENCE (OPTIONAL): 47 Kohm (47Kohm MM o 470ohm MC)
INPUT SENSIVITY: 550 mV (0,9 to 5,0 mV MM variable acceptance) (0,3 to 0,8 mV MC variable acceptance)
RATIO SIGNAL/NOISE : -90dB
SLEW RATE: 13 Volt Line
POWER OUTPUT: 40w+40w 20-20.000Hz max. 0,2%
THD POWER TRASNFORMERS: 2 AUDIO Power CUSTOM Trafo – 1 Volume control
----SOLD---
Integrated Amplifier

BRYSTON B6OR
MADE IN CANADA
Description: Solid-state line-level integrated amplifier. Inputs: Four gold-plated RCA line-level, one tape loop. Outputs: ¼" headphone jack, 1 pair 5-way speaker terminals. Pre-out/main-in RCA jacks.
Preamplifier section: Frequency response: 20Hz-20kHz, ±0.5dB. Maximum output: 15V. IM or THD at 3V output: <0.005%. High-level sensitivity: 500mV. Rated noise: 100dB below 500mV, 20Hz-20kHz. Input sensitivity: 500mV. Input impedance, 50k ohms; tape input impedance, 10k ohms. Preamp and tape output impedance: 100 ohms.
Amplifier section: 60Wpc into 8 ohms (17.8dBW), 100Wpc into 4 ohms (17dBW). THD at rated output (60Wpc): <0.02%, 20Hz-20kHz. IM distortion: <0.01%, 10mW-60W. Noise: 106dB below full output. Slewing rate: >60V/µs. Power bandwidth: 0.5Hz to >100kHz. Damping factor: >500 at 20Hz, ref. 8 ohms. Input sensitivity: 0.775V for full output. Input impedance: 50k ohms. Output impedance: <0.016 ohms.
Dimensions: 17" W by 2.5" H by 12.5" D.
----SOLD---
MADE IN CANADA
Description: Solid-state line-level integrated amplifier. Inputs: Four gold-plated RCA line-level, one tape loop. Outputs: ¼" headphone jack, 1 pair 5-way speaker terminals. Pre-out/main-in RCA jacks.
Preamplifier section: Frequency response: 20Hz-20kHz, ±0.5dB. Maximum output: 15V. IM or THD at 3V output: <0.005%. High-level sensitivity: 500mV. Rated noise: 100dB below 500mV, 20Hz-20kHz. Input sensitivity: 500mV. Input impedance, 50k ohms; tape input impedance, 10k ohms. Preamp and tape output impedance: 100 ohms.
Amplifier section: 60Wpc into 8 ohms (17.8dBW), 100Wpc into 4 ohms (17dBW). THD at rated output (60Wpc): <0.02%, 20Hz-20kHz. IM distortion: <0.01%, 10mW-60W. Noise: 106dB below full output. Slewing rate: >60V/µs. Power bandwidth: 0.5Hz to >100kHz. Damping factor: >500 at 20Hz, ref. 8 ohms. Input sensitivity: 0.775V for full output. Input impedance: 50k ohms. Output impedance: <0.016 ohms.
Dimensions: 17" W by 2.5" H by 12.5" D.
----SOLD---
Integrated Amplifier (Tube)

JADIS ORCHESTRA
MADE IN FRANCE
Power: 40 Watts per channel
Connection : 1 Dock input, 4 line input, line output
Dimensions 530 x 260 x 220
Tubes: 4 x EL34, 6CA7, KT88, 6550, KT90 2 x ECC83/12AX7
Bias : manual - adjustment when the tubes are changed
Weight (kg) 21 kg
Power Consumption (Operational) 300 watt
-----SOLD----
MADE IN FRANCE
Power: 40 Watts per channel
Connection : 1 Dock input, 4 line input, line output
Dimensions 530 x 260 x 220
Tubes: 4 x EL34, 6CA7, KT88, 6550, KT90 2 x ECC83/12AX7
Bias : manual - adjustment when the tubes are changed
Weight (kg) 21 kg
Power Consumption (Operational) 300 watt
-----SOLD----
Integrated Amplifier

SIMAUDIO MOON i.3 RS
MADE IN CANADA
The MOON i-3 RS integrated amplifier combines numerous technologies found in Simaudio MOON preamplifiers and amplifiers. Offering very high quality sonic performance, it represents an affordable alternative to the MOON i-5. Features include remote control operation, a maximum continuous power output rating of 100 watts per channel into 8 ohms / 160 watts into 4 ohms, six line-level inputs including a "home theater ready" input and a preamplifier output.
The RS series of MOON audio components benefit from an even higher standard of manufacturing process than the regular MOON versions. All significant differences are contained within the circuitry and construction of each model.
RS versions are built using different materials and parts in certain areas. For example, printed circuit boards are of a higher temperature grade than that of the military specification FR-4 material we normally use; Their traces are gold-plated instead of a tin/lead composite. As well, all capacitors use improved dielectric materials.
MOON RS models meet and/or exceed stricter manufacturing processes as required to pass many international safety standards such as those imposed by the E-U, Japan and South Korea. Cosmetically, the ONLY difference is the RS logo on the front panel.
----SOLD---
MADE IN CANADA
The MOON i-3 RS integrated amplifier combines numerous technologies found in Simaudio MOON preamplifiers and amplifiers. Offering very high quality sonic performance, it represents an affordable alternative to the MOON i-5. Features include remote control operation, a maximum continuous power output rating of 100 watts per channel into 8 ohms / 160 watts into 4 ohms, six line-level inputs including a "home theater ready" input and a preamplifier output.
The RS series of MOON audio components benefit from an even higher standard of manufacturing process than the regular MOON versions. All significant differences are contained within the circuitry and construction of each model.
RS versions are built using different materials and parts in certain areas. For example, printed circuit boards are of a higher temperature grade than that of the military specification FR-4 material we normally use; Their traces are gold-plated instead of a tin/lead composite. As well, all capacitors use improved dielectric materials.
MOON RS models meet and/or exceed stricter manufacturing processes as required to pass many international safety standards such as those imposed by the E-U, Japan and South Korea. Cosmetically, the ONLY difference is the RS logo on the front panel.
----SOLD---
Integrated Amplifier (Tube)

VTL IT85
MADE IN USA
The VTL IT-85 is a push-pull tetrode tube integrated amplifier with active line-stage preamp, dedicated headphone out, and remote controlled volume. It uses the following tube complement: 4x EL34, 2x 12AU7/ECC82, and 2x 12AT7/ECC81. There are five line level inputs, a buffered preamp out, a processor/amp in, and a tape out. Power output is 60Wpc into 8 ohms and 80Wpc into 4 ohms. This is a gorgeous sounding tube amp that has all the great qualities you'd expect from an revered tube equipment manufacturer of VTL's pedigree. It will drive most any speakers (and all headphones).
----SOLD---
MADE IN USA
The VTL IT-85 is a push-pull tetrode tube integrated amplifier with active line-stage preamp, dedicated headphone out, and remote controlled volume. It uses the following tube complement: 4x EL34, 2x 12AU7/ECC82, and 2x 12AT7/ECC81. There are five line level inputs, a buffered preamp out, a processor/amp in, and a tape out. Power output is 60Wpc into 8 ohms and 80Wpc into 4 ohms. This is a gorgeous sounding tube amp that has all the great qualities you'd expect from an revered tube equipment manufacturer of VTL's pedigree. It will drive most any speakers (and all headphones).
----SOLD---
Integrated Amplifier

EXPOSURE 2010S
MADE IN ENGLAND
Description: Solid-state integrated amplifier with 6 line inputs. Maximum output power: 75Wpc into 8 ohms (18.75dBW). Frequency response: 20Hz–20kHz, ±0.5dB. Input impedance: >14k ohms. Input sensitivity: 250mV. Signal/noise ratio: >100dB, A-weighted (no reference level given). Channel separation: >60dB, 20Hz–20kHz. Total harmonic distortion: <0.05% at 1kHz, rated power.
Dimensions: 17.4" (445mm) W by 4" (100mm) H by 12" (310mm) D. Weight: 15.4 lbs (7kg).
----SOLD---
MADE IN ENGLAND
Description: Solid-state integrated amplifier with 6 line inputs. Maximum output power: 75Wpc into 8 ohms (18.75dBW). Frequency response: 20Hz–20kHz, ±0.5dB. Input impedance: >14k ohms. Input sensitivity: 250mV. Signal/noise ratio: >100dB, A-weighted (no reference level given). Channel separation: >60dB, 20Hz–20kHz. Total harmonic distortion: <0.05% at 1kHz, rated power.
Dimensions: 17.4" (445mm) W by 4" (100mm) H by 12" (310mm) D. Weight: 15.4 lbs (7kg).
----SOLD---
Integrated Amplifier

KRELL KAV-400xi
MADE IN USA
Description: Solid-state, remote-controlled, stereo integrated amplifier with 5 line-level inputs (1 balanced, 3 single-ended, 1 single-ended tape loop) and 1 set of single-ended preamplifier outputs. Power output: 200Wpc into 8 ohms (23dBW), 400Wpc into 4 ohms (23dBW). Output impedance: 0.17 ohm. THD: 1kHz <0.04%; 20kHz <0.25%. Input impedance: 47k ohms. Input sensitivity: 644mV RMS. Power consumption at idle/standby: 20W.
Dimensions: 17.3" (444mm) W by 3.5" (90mm) H by 17" (436mm) D. Weight: 36 lbs (16.4kg).
---SOLD---
MADE IN USA
Description: Solid-state, remote-controlled, stereo integrated amplifier with 5 line-level inputs (1 balanced, 3 single-ended, 1 single-ended tape loop) and 1 set of single-ended preamplifier outputs. Power output: 200Wpc into 8 ohms (23dBW), 400Wpc into 4 ohms (23dBW). Output impedance: 0.17 ohm. THD: 1kHz <0.04%; 20kHz <0.25%. Input impedance: 47k ohms. Input sensitivity: 644mV RMS. Power consumption at idle/standby: 20W.
Dimensions: 17.3" (444mm) W by 3.5" (90mm) H by 17" (436mm) D. Weight: 36 lbs (16.4kg).
---SOLD---
Integrated Amplifier (Tube)

PRIMALUNA PROLOGUE TWO
MADE IN CHINA
Specifications :
Output : 40 watt x 2
Freq. Response: 20Hz-30kHz +/- .5dB
THD: Less than 1 percent at full power
S/N Ratio: 89 db
Input Sensitivity: 300mV
Power Consumption: 300 watts
Dimensions: 11 " x 7.5 " x 15.5" (WxHxD)Weight: 37.5 lbs
Inputs: 4 pair RCA
Outputs: 4 and 8 Ohm speaker taps
Tube Compliment: 2 - 12AX7, 2 - 12AU7, 4 - KT88
----SOLD---
MADE IN CHINA
Specifications :
Output : 40 watt x 2
Freq. Response: 20Hz-30kHz +/- .5dB
THD: Less than 1 percent at full power
S/N Ratio: 89 db
Input Sensitivity: 300mV
Power Consumption: 300 watts
Dimensions: 11 " x 7.5 " x 15.5" (WxHxD)Weight: 37.5 lbs
Inputs: 4 pair RCA
Outputs: 4 and 8 Ohm speaker taps
Tube Compliment: 2 - 12AX7, 2 - 12AU7, 4 - KT88
----SOLD---
Integrated Amplifier

EXPOSURE 2010
MADE IN ENGLAND
Specifications :
Dimensions 90 x 440 x 310
Weight (kg) 7
Amp/Receiver Type Integrated
Impedance (Ohm) 8
Signal-To-Noise Ratio 100
Total Harmonic Distortion Details <0.05% at 1KHz, rated power
Watts Per Channel 75
--SOLD--
MADE IN ENGLAND
Specifications :
Dimensions 90 x 440 x 310
Weight (kg) 7
Amp/Receiver Type Integrated
Impedance (Ohm) 8
Signal-To-Noise Ratio 100
Total Harmonic Distortion Details <0.05% at 1KHz, rated power
Watts Per Channel 75
--SOLD--
Integrated Amplifier

MUSICAL FIDELITY M6i
The M6i 200wpc integrated amp is the first of the completely new M6 series.
---SOLD---
The M6i 200wpc integrated amp is the first of the completely new M6 series.
---SOLD---
Integrated Amplifier (Tube)

BADA DC222
MADE IN CHINA
GENERAL FEATURES:
Top model of the DC222 series
Tube input, tube preamplifier stage and tube impulse stage
High quality stylish full aluminum chassis
Direct coupling employed on critical parts for stunning bass
4 x 12AU7 vacuum tube used in amplifier stages up to output stage
MOSFET high voltage ac supply circuitry
4 pairs of Toshiba high power output transistors
R core transformer for preamplifier session
High grade shielded toroidal transformer for power amplifier session
Japan made motorised ALPS volume control
Wima and Solen capacitors used for final tuning
Sophisticated speaker protection circuit with short circuit protection
Infrared full remote control
Gold plated speaker output posts
Detachable power cord (IEC)
TECHNICAL DATA:
Frequency Response: 20Hz – 20Khz (+/-1.5db)
Output Power : 2 x 95W (8ohms),
2 x 190W (4ohms).
Vacuum Tube: 12AU7 x 4
THD + N: <0.5% (1Khz, 50W)
S/N Ratio: >85db (A weighed)
Input Interface: 4 pairs (RCA)
----SOLD---
MADE IN CHINA
GENERAL FEATURES:
Top model of the DC222 series
Tube input, tube preamplifier stage and tube impulse stage
High quality stylish full aluminum chassis
Direct coupling employed on critical parts for stunning bass
4 x 12AU7 vacuum tube used in amplifier stages up to output stage
MOSFET high voltage ac supply circuitry
4 pairs of Toshiba high power output transistors
R core transformer for preamplifier session
High grade shielded toroidal transformer for power amplifier session
Japan made motorised ALPS volume control
Wima and Solen capacitors used for final tuning
Sophisticated speaker protection circuit with short circuit protection
Infrared full remote control
Gold plated speaker output posts
Detachable power cord (IEC)
TECHNICAL DATA:
Frequency Response: 20Hz – 20Khz (+/-1.5db)
Output Power : 2 x 95W (8ohms),
2 x 190W (4ohms).
Vacuum Tube: 12AU7 x 4
THD + N: <0.5% (1Khz, 50W)
S/N Ratio: >85db (A weighed)
Input Interface: 4 pairs (RCA)
----SOLD---
Integrated Amplifier (Tube)

CANARY AUDIO CA-608
MADE IN USA
CA-608 IS 40 wpc EL34/6CA7 integrated amplifier
TUBE (4 x EL34/6CA7, 2 x 6SN7GTB, 1 x 12AX7)
---SOLD---
MADE IN USA
CA-608 IS 40 wpc EL34/6CA7 integrated amplifier
TUBE (4 x EL34/6CA7, 2 x 6SN7GTB, 1 x 12AX7)
---SOLD---
Integrated Amplifier (Tube)

CARY SLI-80 SIGNATURE
SPECIAL EDITION
MADE IN USA
The SLI-80 Signature Special Edition is based on a pair of KT-88 power tubes per channel in push pull configuration, with 6DJ8/6922 input tubes and a 6SN7 phase splitter. Power output using KT-88 tubes is 80 watts per channel in ultralinear mode and 40 watts in triode mode.
The SLI-80 Signature Special Edition using :
----SOLD---
SPECIAL EDITION
MADE IN USA
The SLI-80 Signature Special Edition is based on a pair of KT-88 power tubes per channel in push pull configuration, with 6DJ8/6922 input tubes and a 6SN7 phase splitter. Power output using KT-88 tubes is 80 watts per channel in ultralinear mode and 40 watts in triode mode.
The SLI-80 Signature Special Edition using :
- Jensen oil and copper capacitors,
- Hexfreds in the power supply,
- CD input wired with Kimber Kable,
- WBT Speaker terminals,
- Grayhill Selector switch,
----SOLD---
Integrated Amplifier

DENSEN BEAT B-100
MADE IN DENMARK
SPECIFICATIONS:
Description: Solid-state integrated amplifier with 6 line-level inputs
Rated output Power: 60Wpc into 8 ohms (17.8dBW); 100Wpc into 4 ohms (17dBW)
Frequency response: 2Hz-200kHz, -0.3dB Input sensitivity: 280mV.
Input impedance: 22k ohms THD 0.01% at 1kHz.
Dimensions: 17" (440mm) W by 2.7" (68mm) H by 11.7" (300mm)
D. Weight: 21 lbs (9.6kg).
----SOLD----
MADE IN DENMARK
SPECIFICATIONS:
Description: Solid-state integrated amplifier with 6 line-level inputs
Rated output Power: 60Wpc into 8 ohms (17.8dBW); 100Wpc into 4 ohms (17dBW)
Frequency response: 2Hz-200kHz, -0.3dB Input sensitivity: 280mV.
Input impedance: 22k ohms THD 0.01% at 1kHz.
Dimensions: 17" (440mm) W by 2.7" (68mm) H by 11.7" (300mm)
D. Weight: 21 lbs (9.6kg).
----SOLD----
Integrated Amplifier

DK DESIGN
VS-1 SIGNATURE MK III
MADE IN USA
The ‘Signature’ Edition Integrated amp, upgraded by hand in our Everett, WA labs, is the answer to that challenge. Installation of our proprietary Active Tube Load circuitry, an upgraded volume control, and major parts and wiring upgrades take the Signature to the next level of musical performance.
The improved clarity is apparent during casual listening, and a focused session reveals low level detail which ushers the listener into a new musical world. Unveiled textures and inner detail take you further from the hi-fi sound and closer to the live performance.
Finish Black, Silver Accents
Rated Power (8Ω) ≥ 150 wpc
Total Harmonic Distortion ≤ 0.1% (1KHz)
Recommended Loading Impedance 4-8Ω
Frequency Response 20Hz-32KHz (±1dB)
Signal-to-Noise Ratio ≥ 90dB
Channel Separation ≥ 60dB (1KHz)
Input Impedance 47KΩ
Input Sensitivity, Analog ≥ 500mv
Input Sensitivity, Phono ≥ 4mv
Inputs 1 balanced, 3 single-end, 1 phono
Dimensions (Imperial) 17" (W ) x 9 1/4 " (H) x 19 1/2" (D)
Dimensions (Metric) 43 cm (W) x 23.5 (H) x 48 (D)
Weight 78lb / 38kg
-----SOLD----
VS-1 SIGNATURE MK III
MADE IN USA
The ‘Signature’ Edition Integrated amp, upgraded by hand in our Everett, WA labs, is the answer to that challenge. Installation of our proprietary Active Tube Load circuitry, an upgraded volume control, and major parts and wiring upgrades take the Signature to the next level of musical performance.
The improved clarity is apparent during casual listening, and a focused session reveals low level detail which ushers the listener into a new musical world. Unveiled textures and inner detail take you further from the hi-fi sound and closer to the live performance.
Finish Black, Silver Accents
Rated Power (8Ω) ≥ 150 wpc
Total Harmonic Distortion ≤ 0.1% (1KHz)
Recommended Loading Impedance 4-8Ω
Frequency Response 20Hz-32KHz (±1dB)
Signal-to-Noise Ratio ≥ 90dB
Channel Separation ≥ 60dB (1KHz)
Input Impedance 47KΩ
Input Sensitivity, Analog ≥ 500mv
Input Sensitivity, Phono ≥ 4mv
Inputs 1 balanced, 3 single-end, 1 phono
Dimensions (Imperial) 17" (W ) x 9 1/4 " (H) x 19 1/2" (D)
Dimensions (Metric) 43 cm (W) x 23.5 (H) x 48 (D)
Weight 78lb / 38kg
-----SOLD----
Integrated Amplifier (Tube)

AUDIO ANALOGUE
PRIMO CENTO VT
MADE IN ITALY
Primo Cento VT
100 watt Hybrid Integrated Amp
---SOLD---
PRIMO CENTO VT
MADE IN ITALY
Primo Cento VT
100 watt Hybrid Integrated Amp
---SOLD---
Integrated Amplifier (Tube)

OPERA CONSONANCE
CYBER-30
MADE IN CHINA
Cyber-30 is a single-ended class A integrated amplifier. It uses no global feedback. The 12AX7/ECC83 is a dual triode, which acts as input and drive tube. The 2A3 is self biased . AC voltage applied to the input goes first to the front panel volume control and then to the 12AX7/ECC83. The 12AX7/ECC83 provides voltage gain and drives the 2A3 output tube. The 2A3 is transformer-coupled to the load.
SPECIFICATION:
Output impedance for speaker : 16 W , 8 W
Output impedance for headphone : 10 W - 600 W
Output power : 3.5 W x 2 RMS 1kHz
Frequency response : 10Hz - 36kHz - 3dB (1W)
Harmonic distortion : <1% (1W, 1KHz)
S/N ratio : 90dB
Input sensitivity : 600mV
Input connector : 1 set (RCA)
Power consumption : 86W
Vacuum tubes : 2A3 x 2, 12AX7/ECC83 x 1
Dimension : 320 (L) x 260 (W) x 150(H) mm
----SOLD---
CYBER-30
MADE IN CHINA
Cyber-30 is a single-ended class A integrated amplifier. It uses no global feedback. The 12AX7/ECC83 is a dual triode, which acts as input and drive tube. The 2A3 is self biased . AC voltage applied to the input goes first to the front panel volume control and then to the 12AX7/ECC83. The 12AX7/ECC83 provides voltage gain and drives the 2A3 output tube. The 2A3 is transformer-coupled to the load.
SPECIFICATION:
Output impedance for speaker : 16 W , 8 W
Output impedance for headphone : 10 W - 600 W
Output power : 3.5 W x 2 RMS 1kHz
Frequency response : 10Hz - 36kHz - 3dB (1W)
Harmonic distortion : <1% (1W, 1KHz)
S/N ratio : 90dB
Input sensitivity : 600mV
Input connector : 1 set (RCA)
Power consumption : 86W
Vacuum tubes : 2A3 x 2, 12AX7/ECC83 x 1
Dimension : 320 (L) x 260 (W) x 150(H) mm
----SOLD---
Integrated Amplifier

CLASSE CAP-150
MADE IN CANADA
CAP-150 FEATURES
Remote control featuring adjustments for both volume and mute. Contoured slimline chassis.
Inputs featuring AUX/PHONO, VIDEO, CD, TUNER, BALANCED inputs, PREAMP OUT outputs to be used with an external power amplifier, AMP IN inputs to be used with an external
preamplifier. Front panel controls include INPUT SELECTOR, BALANCE, VOLUME, TAPE,
SEPARATE, MUTE and POWER. Special Classé front panel in Soft Shadow Silver finishes.
CAP-150 SPECIFICATIONS
PREAMPLIFIER SECTION
Frequency response: 20 Hz to 20 KHz, + 0.1 dB
Maximum Output: 20 Volts Peak to Peak
S/N Ratio: -110 dB “A” weighted
THD+N: 0.006%
Input Impedance: 12 Kohms for balanced
33 Kohms for single ended
Output Impedance: 50 ohms
Gain: 17 dB
Crosstalk: -75 dB at 1 KHz
AMPLIFIER SECTION
Output impedance: 0.17 ohm
Input impedance: 118 Kohms
Gain: 29 dB
S/N ratio: -110 dB “A” weighted
THD+N 0.002%
Output power: 150 Watts/channel into 8 ohms
225 Watts/channel into 4 ohms
COMBINED
S/N ratio: -90 dB “A” weighted
THD+N: 0.005%
Crosstalk: -75dB
Dimensions: Gross: 24" x 10.25" x21.25"
Net: 19" x 5" x 17"
Weight: Gross: 40 lbs.
Net: 35 lbs.
----SOLD----
MADE IN CANADA
CAP-150 FEATURES
Remote control featuring adjustments for both volume and mute. Contoured slimline chassis.
Inputs featuring AUX/PHONO, VIDEO, CD, TUNER, BALANCED inputs, PREAMP OUT outputs to be used with an external power amplifier, AMP IN inputs to be used with an external
preamplifier. Front panel controls include INPUT SELECTOR, BALANCE, VOLUME, TAPE,
SEPARATE, MUTE and POWER. Special Classé front panel in Soft Shadow Silver finishes.
CAP-150 SPECIFICATIONS
PREAMPLIFIER SECTION
Frequency response: 20 Hz to 20 KHz, + 0.1 dB
Maximum Output: 20 Volts Peak to Peak
S/N Ratio: -110 dB “A” weighted
THD+N: 0.006%
Input Impedance: 12 Kohms for balanced
33 Kohms for single ended
Output Impedance: 50 ohms
Gain: 17 dB
Crosstalk: -75 dB at 1 KHz
AMPLIFIER SECTION
Output impedance: 0.17 ohm
Input impedance: 118 Kohms
Gain: 29 dB
S/N ratio: -110 dB “A” weighted
THD+N 0.002%
Output power: 150 Watts/channel into 8 ohms
225 Watts/channel into 4 ohms
COMBINED
S/N ratio: -90 dB “A” weighted
THD+N: 0.005%
Crosstalk: -75dB
Dimensions: Gross: 24" x 10.25" x21.25"
Net: 19" x 5" x 17"
Weight: Gross: 40 lbs.
Net: 35 lbs.
----SOLD----