THE HIGH END AUDIO STORE
  • HOME
  • SPEAKER
  • CD PLAYER
  • CD TRANSPORT
  • INTEGRATED AMPLIFIER
  • POWER AMPLIFIER
  • PRE AMPLIFIER
  • DAC
  • TURNTABLE
  • CABLE
  • TUBES
  • PHONO STAGE
  • HOME THEATER
  • ACCESORIES
  • IPOD & STUFF
  • OTHERS
  • CONTACT US

Phono Stage

Picture
ROGUE AUDIO STEALTH
MADE IN USA




Conditions : Pre-Owned, Excellent
Price : Rp 7.500.000


 Phono Stage (Tube)

Picture
ROGUE AUDIO ARES
MADE IN USA








Condition : Brand New
Price : Rp 17.000.000,-

Phono Stage (Tube)

Picture
BALANCED AUDIO TECHNOLOGY
VK-P5


MADE IN USA

Inputs: XLR No RCA Yes
Outputs: XLR
Gain @ 1kHz:
   Direct-low position: 50 dB
   Direct-high position: 55 dB
   Step-up low: NA
   Step-up high: NA
Signal-to-noise ratio (A-weighted referenced to 1mV):
   Direct-low position 71 dB
   Direct-high position 73 dB
   Step-up high: NA
Cartridge loading:
   Resistance: 100 O to 47 kO
   Capacitance: 100 pF to 1000 µF
Polarity selectable inverting/non-inverting: No
Power supply energy storage: 140 joules
Power consumption-maximum: 150 VA
Dimensions: (WHD): 19" x 5.75" x 15.5"
Weight-unpackaged: 30 lb.


----SOLD-----


Phono Stage

Picture
MUSICAL FIDELITY X-LPS V8

The circuitry in the X-LPSv8 is similar to that used in expensive electronics. The RIAA is very accurate, the noise ratio is excellent and overload margins are good. Generally, its technical performance on both MM and MC is equal to some highly expensive stand-alone phono stages. Subjectives are personal, but we think that this phonostage will stand comparison with the best. It doesn't have a high price tag so many will not even look or listen to this little marvel. Forget the price and listen to the music.

----SOLD---


Phono Stage (Tube)

Picture
CONRAD JOHNSON EV-1
MADE IN USA

The EV1 was a separate phono equalization preamplifier designed to provide the additional gain and RIAA equalization that modern phono cartridges require. Based on the circuit used in conrad-johnson’s acclaimed Premier Fifteen, the EV1 used a single-ended triode input amplifier comprised of both sections of a miniature twin–triode tube connected in parallel for reduced noise. A second single-ended triode amplifier provided added gain. A passive network of precision components between these two stages set the required frequency equalization. A direct coupled cathode follower output stage yielded a low output impedance. The EV1’s circuit employs no negative feedback loop. The EV1 was a simple, low-noise, high-gain device well suited for use with a wide range of phono cartridges of both moving magnet and moving coil types.
Specifications :
Gain: 49 dB
Phono Overload: 200 mV
Phono Equalization: within +/- .25 dB of RIAA
Hum and Noise: 78 dB below 10mV input
Phase: phase correct
Mechanical: 14.375D x 19W x 3.315H inches
Weight: 14.5 lbs.


----SOLD---


Phono Stage

Picture
MUSICAL FIDELITY
X-LPS V3


MM input
Sensitivity 3mV for 350mV output at 1kHz
Input impedance 47K Ohms
THD < 0.01% at 1kHz, 350mV out
Input overload margin 30dB
S/N ratio > 75dB unweighted > 83dB "A" weighted

MC input
Sensitivity 350μV for 350mV output at 1kHz
Input impedance 100 Ohms
THD < 0.01% at 1kHz, 350mV out
Input overload margin 30dB
S/N ratio > 65dB unweighted
> 74dB "A" weighted
General
RIAA accuracy ± 0.25dB 20Hz to 20kHz
Power requirement 12 - 0 - 12Volts AC 500mA
(via mains adaptor supplied)
Dimensions 180mm (7.1") wide
88.2mm (3.5") high including feet
208mm (8.2") deep
Weights Unit, net : 2.5 kg (5 lbs 8 oz)
Adaptor, net : 0.45 kg (1 lb)
Total packed : 3.1 kg (6 lbs 13 ozs)



----SOLD---

Phono Stage

Picture
SIMAUDIO MOON LP3
MADE IN CANADA

Significant Design Features:
· End-user adjustable impedance loading (100Ω and 47kΩ)
· End-user adjustable capacitance loading (0pF and 100pF)
· End-user adjustable gain for moving magnet (40dB) & moving coil cartridges (60dB)
· Two-layer PCB tracings using pure copper for low impedance characteristics. The
  advantages include better circuit layouts resulting in a much shorter signal path
  and a vastly improved signal-to-noise ratio
· Inductive DC Filtering for a significantly lower noise floor
· Accurate matching of military-grade components with ultra-tight tolerances
  using surface-mount technology for extremely short signal paths
· Compact, rigid all-aluminum chassis with gold-plated RCA connectors.


----SOLD----


Powered by Create your own unique website with customizable templates.