Power Amplifier
KRELL KAV 250a
MADE IN USA
Solid State power amp
250 Watts per channel into 8 ohms
500 Watts per channel into 4 ohms
1000 Watts per channel into 2 ohms
-----SOLD------
MADE IN USA
Solid State power amp
250 Watts per channel into 8 ohms
500 Watts per channel into 4 ohms
1000 Watts per channel into 2 ohms
-----SOLD------
Power Amplifier (Tube)
AUDIO RESEARCH VS115
MADE IN USA
Specifications:
POWER OUTPUT:120 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 120 watts, below .05% at 1 watt.
FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.8Hz to 100kHz.
INPUT SENSITIVITY:1.6V RMS Single-ended or Balanced for rated output. (26dB gain into 8 ohms).
INPUT IMPEDANCE: 150K ohms Single-ended, 300K Balanced.
OUTPUT TAPS: 8 ohms, 4 ohms.
OUTPUT REGULATION: Approximately 1.2dB 8 ohm load to open circuit (Damping factor approx. 8).
OUTPUT POLARITY: Non-inverting. SE or BAL PIN 2+ (IEC268)
HUM & NOISE: Less that 0.2mV RMS 104dB below rated output (IHF weighted, input shorted).
POWER SUPPLY ENERGY STORAGE: Approximately 332 joules.
POWER REQUIREMENTS:105-125VAC 60Hz (210-250VAC 50Hz) 690 watts at rated output, 900 watts maximum, 400 watts at "idle."
TUBES REQUIRED: 4 - Matched pair 6550 — Power Output; 4 - 6H30 gain and driver.
DIMENSIONS: 17.5" (44.5 cm) W x 7.9" (20.1 cm) H x 19"(48.3 cm) D. Rear connectors extend .88" beyond chassis.
WEIGHT: 62 lbs. (28.2 kg) Net; 70 lbs. (31.8 kg) Shipping.
----SOLD----
MADE IN USA
Specifications:
POWER OUTPUT:120 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 120 watts, below .05% at 1 watt.
FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.8Hz to 100kHz.
INPUT SENSITIVITY:1.6V RMS Single-ended or Balanced for rated output. (26dB gain into 8 ohms).
INPUT IMPEDANCE: 150K ohms Single-ended, 300K Balanced.
OUTPUT TAPS: 8 ohms, 4 ohms.
OUTPUT REGULATION: Approximately 1.2dB 8 ohm load to open circuit (Damping factor approx. 8).
OUTPUT POLARITY: Non-inverting. SE or BAL PIN 2+ (IEC268)
HUM & NOISE: Less that 0.2mV RMS 104dB below rated output (IHF weighted, input shorted).
POWER SUPPLY ENERGY STORAGE: Approximately 332 joules.
POWER REQUIREMENTS:105-125VAC 60Hz (210-250VAC 50Hz) 690 watts at rated output, 900 watts maximum, 400 watts at "idle."
TUBES REQUIRED: 4 - Matched pair 6550 — Power Output; 4 - 6H30 gain and driver.
DIMENSIONS: 17.5" (44.5 cm) W x 7.9" (20.1 cm) H x 19"(48.3 cm) D. Rear connectors extend .88" beyond chassis.
WEIGHT: 62 lbs. (28.2 kg) Net; 70 lbs. (31.8 kg) Shipping.
----SOLD----
Power Amplifier
PRIMARE A 34.2
MADE IN SWEDEN
SPECIFICATIONS :
Output power 2 x 150W / 8 ohm THD+N <0.1%
Inputs 2x RCA / 2x XLR switchable, RS232, trigger (12V)
Input impedance 15kohm RCA/XLR
Output Impedance 0.03ohm at 1kHz
Gain 30dB unbalanced, 26dB balanced
Frequency response 20 Hz – 20kHz, -0.5dB
Signal to Noise 20-20kHz unweighted 105dBV
THD + N < 0,005% (1kHz, 100W, 8 ohm)
THD + N <0.02% 20Hz-20Khz (10W 8 ohm)
Power consumption Standby: 0.3W, Idle: 24W
Dimensions (wxdxh) 430 x 385 x 105 mm
Weight 10.5 kg
------SOLD------
MADE IN SWEDEN
SPECIFICATIONS :
Output power 2 x 150W / 8 ohm THD+N <0.1%
Inputs 2x RCA / 2x XLR switchable, RS232, trigger (12V)
Input impedance 15kohm RCA/XLR
Output Impedance 0.03ohm at 1kHz
Gain 30dB unbalanced, 26dB balanced
Frequency response 20 Hz – 20kHz, -0.5dB
Signal to Noise 20-20kHz unweighted 105dBV
THD + N < 0,005% (1kHz, 100W, 8 ohm)
THD + N <0.02% 20Hz-20Khz (10W 8 ohm)
Power consumption Standby: 0.3W, Idle: 24W
Dimensions (wxdxh) 430 x 385 x 105 mm
Weight 10.5 kg
------SOLD------
Power Amplifier (Tube)
ROGUE AUDIO
M120 MONOBLOCKS
MADE IN USA
General Features:
- Ultra-wide bandwith output transformers
- Massive high storage power supply
- Both 4 and 8 ohm output taps provided
- External switch for triode or ultralinear operation
- (4) KT88, (2) 12AU7, (1) 12AX7 tubes (ea.)
- Welded-wire tube cage
- Mechanically isolated transformers
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- All precision components
- Heavy (2 ounce) copper circuit board
- Machined aluminum faceplate
- Matched octets of output tubes
- Entirely designed and built in the USA
- Fully tested, burned-in, and auditioned
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Specifications:
- output power: 120WPC minimum
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1% at rated power
- input sensitivity: 1.0V RMS
- input impedance: 200K Ohms
- dimensions: 14½"W x 7"H x 19"D
- weight: 42 lbs. ea. (Magnum version: 50 lbs. ea.)
- power requirements: 115/230V - 50/60Hz
Condition : Pre-Owned, Excellent
Price : Rp 19.000.000,-
M120 MONOBLOCKS
MADE IN USA
General Features:
- Ultra-wide bandwith output transformers
- Massive high storage power supply
- Both 4 and 8 ohm output taps provided
- External switch for triode or ultralinear operation
- (4) KT88, (2) 12AU7, (1) 12AX7 tubes (ea.)
- Welded-wire tube cage
- Mechanically isolated transformers
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- All precision components
- Heavy (2 ounce) copper circuit board
- Machined aluminum faceplate
- Matched octets of output tubes
- Entirely designed and built in the USA
- Fully tested, burned-in, and auditioned
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Specifications:
- output power: 120WPC minimum
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1% at rated power
- input sensitivity: 1.0V RMS
- input impedance: 200K Ohms
- dimensions: 14½"W x 7"H x 19"D
- weight: 42 lbs. ea. (Magnum version: 50 lbs. ea.)
- power requirements: 115/230V - 50/60Hz
Condition : Pre-Owned, Excellent
Price : Rp 19.000.000,-
Power Amplifier
NU FORCE REFERENCE 8B
MONOBLOCKS
MADE IN USA
Specifications:
Power: 100W at 8 Ohms
Damping Factor: Greater than 4000
Input Impedance: 47k Ohms
Gain: 26 dB
Signal to Noise Ratio: 100dB at 100W
-------SOLD-------
MONOBLOCKS
MADE IN USA
Specifications:
Power: 100W at 8 Ohms
Damping Factor: Greater than 4000
Input Impedance: 47k Ohms
Gain: 26 dB
Signal to Noise Ratio: 100dB at 100W
-------SOLD-------
YAMAHA B6
MADE IN JAPAN
SPECIFICATIONS :
Power output: 200 watts per channel into 8Ω (stereo)
Frequency response: 1Hz to 100kHz
Total harmonic distortion: 0.003%
Damping factor: 200 Input sensitivity: 1.41V
Signal to noise ratio: 127dB
Dimensions: 290 x 176.5 x 290mm
Weight: 9kg
Condition : Pre-Owned, Excellent
Price : Rp 7.500.000,-
MADE IN JAPAN
SPECIFICATIONS :
Power output: 200 watts per channel into 8Ω (stereo)
Frequency response: 1Hz to 100kHz
Total harmonic distortion: 0.003%
Damping factor: 200 Input sensitivity: 1.41V
Signal to noise ratio: 127dB
Dimensions: 290 x 176.5 x 290mm
Weight: 9kg
Condition : Pre-Owned, Excellent
Price : Rp 7.500.000,-
Power Amplifier
MARK LEVINSON NO.27
MADE IN USA
Specifications :
Power output: 100 watts per channel into 8Ω (stereo)
Frequency response: 4Hz to 122kHz
Total harmonic distortion: 0.3%
Gain: 26.9 dB
Dimensions: 483 x 185 x 360mm
Weight: 43.1kg
-----SOLD------
MADE IN USA
Specifications :
Power output: 100 watts per channel into 8Ω (stereo)
Frequency response: 4Hz to 122kHz
Total harmonic distortion: 0.3%
Gain: 26.9 dB
Dimensions: 483 x 185 x 360mm
Weight: 43.1kg
-----SOLD------
THRESHOLD S-300
MADE IN USA
Specifications :
Power output: 150 watts per channel into 8Ω (stereo)
Frequency response: 7Hz to 100kHz
Total harmonic distortion: 0.1%
Gain: 26.6 dB
Signal to noise ratio: 100dB
Semiconductors: 14 x transistors per channel (output)
Dimensions: 8.72 x 19 x 13.125 inches
Weight: 56lbs
------SOLD-----
MADE IN USA
Specifications :
Power output: 150 watts per channel into 8Ω (stereo)
Frequency response: 7Hz to 100kHz
Total harmonic distortion: 0.1%
Gain: 26.6 dB
Signal to noise ratio: 100dB
Semiconductors: 14 x transistors per channel (output)
Dimensions: 8.72 x 19 x 13.125 inches
Weight: 56lbs
------SOLD-----
Power Amplifier
MCINTOSH MC7100
MADE IN USA
SPECIFICATIONS:
* Power Output: … Stereo Setting: 100w/ch into 8 ohms … Stereo Setting: 150w/ch into 4 ohms. … Mono Setting: 300w into 8 ohms * Frequency Response: 20-20kHz (+0 -0.25dB) * Distortion: 0.005% * Noise and hum: -115dBA * Output direct coupled for 4 to 8 ohms. * Damping factor 100 or greater * Input impedance 20k * Input sensitivity 1.4v * Sentry Monitor * Power Guard * Dimensions: … 17.5" Width … 3.6” Height … 15.0" Depth * Weight: 24 pounds
-----SOLD------
MADE IN USA
SPECIFICATIONS:
* Power Output: … Stereo Setting: 100w/ch into 8 ohms … Stereo Setting: 150w/ch into 4 ohms. … Mono Setting: 300w into 8 ohms * Frequency Response: 20-20kHz (+0 -0.25dB) * Distortion: 0.005% * Noise and hum: -115dBA * Output direct coupled for 4 to 8 ohms. * Damping factor 100 or greater * Input impedance 20k * Input sensitivity 1.4v * Sentry Monitor * Power Guard * Dimensions: … 17.5" Width … 3.6” Height … 15.0" Depth * Weight: 24 pounds
-----SOLD------
Power Amplifier
JEFF ROWLAND
MODEL ONE
MADE IN USA
Specifications
Power output: 60 watts per channel into 8Ω (stereo)
Frequency response: 20Hz to 20kHz
Total harmonic distortion: 0.035%
Damping factor: 200
Gain: 32 dB
Speaker load impedance: 2Ω (minimum)
------SOLD--------
MODEL ONE
MADE IN USA
Specifications
Power output: 60 watts per channel into 8Ω (stereo)
Frequency response: 20Hz to 20kHz
Total harmonic distortion: 0.035%
Damping factor: 200
Gain: 32 dB
Speaker load impedance: 2Ω (minimum)
------SOLD--------
Power Amplifier (Tube)
SOUND VALVES M40
MADE IN USA
Tube monoblocks power amp uses 2- EL34 and 1-6GH8 or 6U8 per amp
-----SOLD-----
MADE IN USA
Tube monoblocks power amp uses 2- EL34 and 1-6GH8 or 6U8 per amp
-----SOLD-----
Power Amplifier
AUDIOLAB 8200P
MADE IN UK
General Description: Stereo Power Amplifier
Output Power: 2 x 100W RMS 8 ohms
2 x 150W RMS 4 ohms
Frequency Response: 20 Hz-20 kHz ±0.3 dB
0.1Hz-75 kHz -3 dB.
Gain: 29.0 dB at1kHz
Total Harmonic Distortion: Less than 0.05%
Signal to Noise Ratio: Better than 95 dB
Input Sensitivity (RCA): 1V rms for 100W into 8
Input Impedance (RCA): 50kΩ
Power Consumption: 500 VA
Dimensions (W x H x D): 445×74×337mm- including feet, terminals and controls
Weight: Net: 8.7 kg Shipping: 10 kg
-------SOLD------
MADE IN UK
General Description: Stereo Power Amplifier
Output Power: 2 x 100W RMS 8 ohms
2 x 150W RMS 4 ohms
Frequency Response: 20 Hz-20 kHz ±0.3 dB
0.1Hz-75 kHz -3 dB.
Gain: 29.0 dB at1kHz
Total Harmonic Distortion: Less than 0.05%
Signal to Noise Ratio: Better than 95 dB
Input Sensitivity (RCA): 1V rms for 100W into 8
Input Impedance (RCA): 50kΩ
Power Consumption: 500 VA
Dimensions (W x H x D): 445×74×337mm- including feet, terminals and controls
Weight: Net: 8.7 kg Shipping: 10 kg
-------SOLD------
Power Amplifier (Tube)
MANLEY SNAPPER
Monoblocks Amp
MADE IN USA
Specifications :
· 100 Watt partial triode (UltraLinear) EL-34 output stage is tolerant of a wider variety of output load conditions than pure pentode.
· Precise and balanced signal path from input to output. Circuit self-balances with either single-ended or balanced inputs. [Don't let either speaker terminal contact chassis, earth or any other ground.
· Switch-selectable RCA unbalanced inputs, or XLR balanced inputs. RCA jack input impedance about 330 kOhms, XLR 15 kOhms. If one input is not occupied, the input selector switch may then be used as a poor-man's MUTE switch. Handy for checking the bias, swapping input cables, etc..
· 100 W spec: 15 Hz - 40 kHz into 5 Ohms
· Puts out 100W into an 8 Ohm load.
· Unit weight: 38 lbs.
------SOLD-------
Monoblocks Amp
MADE IN USA
Specifications :
· 100 Watt partial triode (UltraLinear) EL-34 output stage is tolerant of a wider variety of output load conditions than pure pentode.
· Precise and balanced signal path from input to output. Circuit self-balances with either single-ended or balanced inputs. [Don't let either speaker terminal contact chassis, earth or any other ground.
· Switch-selectable RCA unbalanced inputs, or XLR balanced inputs. RCA jack input impedance about 330 kOhms, XLR 15 kOhms. If one input is not occupied, the input selector switch may then be used as a poor-man's MUTE switch. Handy for checking the bias, swapping input cables, etc..
· 100 W spec: 15 Hz - 40 kHz into 5 Ohms
· Puts out 100W into an 8 Ohm load.
· Unit weight: 38 lbs.
------SOLD-------
ATMA-SPHERE S30 MK II
MADE IN USA
SPECIFICATIONS:
MADE IN USA
SPECIFICATIONS:
- 30 watts/ch into 8-ohm load/45 watts into 16-ohm load
- power bandwidth: 2Hz-75KHz within 1/2 db
- frequency response (1 watt): 1Hz-100KHz within 3 dB
- THD typically 1% at full power
- IM distortion typically under .04% at full power
- phase shift: less than 1 degree @ 20KHz
- input impedance: 100K single-ended, 200K balanced
- output section risetime: 600V/micro-sec.
- stability: stable with all loads and inputs
- feedback: 2db
- power consumption: 400 watts
- tube complement: 10) 6AS7G output tube
- 6) 6SN7 driver tube
Power Amplifier (Tube)
SYNTHESIS RENAISSANCE
MADE IN ITALY
Specifications:
Sensitivity: 1 Volt
Input impedance: 82 Kohm
Output impedance: 6 ohm
Power output: 15 Watts into 6 ohm
Frequency response : 20Hz to 20 KHz
Configuration: Triode
Tube compliment: 4 x 12AU7/6189
4 x EL34/6CA7
Power input: 210@240v 50Hz
Power consumption: 110 Watts Max
Dimensions (w,d,h): 320x220x160 mm
Weight: 10 Kg
-----SOLD-----
MADE IN ITALY
Specifications:
Sensitivity: 1 Volt
Input impedance: 82 Kohm
Output impedance: 6 ohm
Power output: 15 Watts into 6 ohm
Frequency response : 20Hz to 20 KHz
Configuration: Triode
Tube compliment: 4 x 12AU7/6189
4 x EL34/6CA7
Power input: 210@240v 50Hz
Power consumption: 110 Watts Max
Dimensions (w,d,h): 320x220x160 mm
Weight: 10 Kg
-----SOLD-----
Power Amplifier (Tube)
AUDIO RESEARCH VT50
MADE IN USA
Specifications :
Power output : 45 watts per channel continuous from 30Hz to 15kHz. Approximate actual power available at "clipping" 50 watts (1kHz)
Power bandwidth : (-3dB points) 12Hz to 45kHz
Frequency response :(-3dB points at 1 watt) 1.5Hz to 50 kHz
Input sensitivity :1.95V RMS (Bal or SE) for rated output. (22.8 dB gain into 16 ohms.)
Input impedance :200K ohms Balanced, 100K ohms Single-ended
Output regulation:Approximately 1.3dB 16 ohm load to open circuit
Overall negative feedback: 8.5 dB
Damping factor : 6
Distortion :1kHz total harmonic distortion typically 1% at 45 watts, below .05% at 1 watt.
Slew rate : 10 volts/microsecond
Rise time: 7 microseconds
Hum & noise: Less than 0.25mV RMS < 100dB below rated output (IHF weighted, input shorted)
Pwr supply energy: 354 joules
Power requirements : 105-125VAC 60Hz (210-250VAC 50Hz) 275 watts at rated output, 330 watts maximum, 200 watts at "idle"
Tube complement : (2 matched pairs) 6550C, (2) 6922 driver; (2) 6922 input.
Dimensions :19" (48.3 cm) W x 7" (17.8 cm) H x 15" (38.1 cm) D. Handles extend 1.5" (3.8 cm) forward
Weight : 41 lbs. (18.6 kg) Net; 54 lbs. (24.5 kg) Shipping.
-----SOLD-----
MADE IN USA
Specifications :
Power output : 45 watts per channel continuous from 30Hz to 15kHz. Approximate actual power available at "clipping" 50 watts (1kHz)
Power bandwidth : (-3dB points) 12Hz to 45kHz
Frequency response :(-3dB points at 1 watt) 1.5Hz to 50 kHz
Input sensitivity :1.95V RMS (Bal or SE) for rated output. (22.8 dB gain into 16 ohms.)
Input impedance :200K ohms Balanced, 100K ohms Single-ended
Output regulation:Approximately 1.3dB 16 ohm load to open circuit
Overall negative feedback: 8.5 dB
Damping factor : 6
Distortion :1kHz total harmonic distortion typically 1% at 45 watts, below .05% at 1 watt.
Slew rate : 10 volts/microsecond
Rise time: 7 microseconds
Hum & noise: Less than 0.25mV RMS < 100dB below rated output (IHF weighted, input shorted)
Pwr supply energy: 354 joules
Power requirements : 105-125VAC 60Hz (210-250VAC 50Hz) 275 watts at rated output, 330 watts maximum, 200 watts at "idle"
Tube complement : (2 matched pairs) 6550C, (2) 6922 driver; (2) 6922 input.
Dimensions :19" (48.3 cm) W x 7" (17.8 cm) H x 15" (38.1 cm) D. Handles extend 1.5" (3.8 cm) forward
Weight : 41 lbs. (18.6 kg) Net; 54 lbs. (24.5 kg) Shipping.
-----SOLD-----
Power Amplifier
DENON POA-6600
MADE IN JAPAN
Denon POA-6600, Monoblocks
Manufacturer: NIPPON COLUMBIA, Japan
Specifications:
Rated power: 250 watts into 8 ohms, 20Hz-20kHz, <0.02% THD, 450 watts into 4 ohms, DIN 1 kHz
Dynamic power: 650 watts into 4 ohms, 1100 watts into 1 ohm
THD: <0.002% (-3 dB at rated output into 8 ohms)
Intermodulation distortion: <0.002% (60 Hz/7 kHz: 4/1 at rated power, 8 ohms)
Power bandwidth: 5 Hz - 80 kHz (8 ohms, 0.02% THD)
Frequency: 1 Hz - 300 kHz (+0 /-3dB, 1 W)
Input sensitivity: 1 V (adjustable)
Input impedance: 25 kohms (RCA), 10 kohms (XLR)
Output impedance: 0.1 ohms (1 kHz)
External voltage: 123 dB (IHF, A-rating, XLR)
Inputs: RCA and XLR
Outputs: Speaker A or B: 4 Ohms - 16 Ohms/A and B: 8 ohms - 16 ohms
Dimensions: 310 x 207 x 456 mm
Power consumption: 350 W
Weight (per piece): 15.6 kilograms
-------SOLD------
MADE IN JAPAN
Denon POA-6600, Monoblocks
Manufacturer: NIPPON COLUMBIA, Japan
Specifications:
Rated power: 250 watts into 8 ohms, 20Hz-20kHz, <0.02% THD, 450 watts into 4 ohms, DIN 1 kHz
Dynamic power: 650 watts into 4 ohms, 1100 watts into 1 ohm
THD: <0.002% (-3 dB at rated output into 8 ohms)
Intermodulation distortion: <0.002% (60 Hz/7 kHz: 4/1 at rated power, 8 ohms)
Power bandwidth: 5 Hz - 80 kHz (8 ohms, 0.02% THD)
Frequency: 1 Hz - 300 kHz (+0 /-3dB, 1 W)
Input sensitivity: 1 V (adjustable)
Input impedance: 25 kohms (RCA), 10 kohms (XLR)
Output impedance: 0.1 ohms (1 kHz)
External voltage: 123 dB (IHF, A-rating, XLR)
Inputs: RCA and XLR
Outputs: Speaker A or B: 4 Ohms - 16 Ohms/A and B: 8 ohms - 16 ohms
Dimensions: 310 x 207 x 456 mm
Power consumption: 350 W
Weight (per piece): 15.6 kilograms
-------SOLD------
Power Amplifier (Tube)
ROGUE AUDIO
MAGNUM 88
MADE IN USA
General Features:
- Ultra-wide bandwidth output transformers
- Massive fully regulated high voltage supply
- Matched quad output tubes
- User selectable 4 and 8 ohm output taps
- User selectable triode or ultralinear output
- (4) KT88/6550, (4) 12AU7, (2) 12AX7 tube complement
- Integral tube cage
- Machined aluminum faceplate
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- Mechanically isolated transformers
- Heavy (2 ounce) copper circuit board
- All precision components
- Fully tested, burned in, and auditioned
- 3 year limited warranty (6 months on tubes)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Specifications:
- output power: 60WPC minimum
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1.0% at rated power
- input sensitivity: 1.0V RMS
- input impedance: 200K Ohms
- dimensions: 18"W x 15¾"D x 7"H
- weight: 55 lbs.
- power requirements: 115/230V - 50 - 60Hz
-----SOLD------
MAGNUM 88
MADE IN USA
General Features:
- Ultra-wide bandwidth output transformers
- Massive fully regulated high voltage supply
- Matched quad output tubes
- User selectable 4 and 8 ohm output taps
- User selectable triode or ultralinear output
- (4) KT88/6550, (4) 12AU7, (2) 12AX7 tube complement
- Integral tube cage
- Machined aluminum faceplate
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- Mechanically isolated transformers
- Heavy (2 ounce) copper circuit board
- All precision components
- Fully tested, burned in, and auditioned
- 3 year limited warranty (6 months on tubes)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Specifications:
- output power: 60WPC minimum
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1.0% at rated power
- input sensitivity: 1.0V RMS
- input impedance: 200K Ohms
- dimensions: 18"W x 15¾"D x 7"H
- weight: 55 lbs.
- power requirements: 115/230V - 50 - 60Hz
-----SOLD------
Power Amplifier
ARCAM P1 MONOBLOCK
MADE IN UK
Specifications :
-----SOLD-----
MADE IN UK
Specifications :
- 175wpc continuous power output (8ohms, one channel driven)
- 250wpc continuous power output (4ohms, 1kHz, one channel driven)
- Fully discrete transistor power amp stages with temperature compensation
- Current feedback design ensuring wide bandwidth for high resolution audio
- Balanced (XLR) and unbalanced (RCA Phono) input
- All DC coupled signal path for enhanced bass control
- Twin RCA Phono input for "loop through" to second power amp
- Massive toroid mains transformer
- User switchable between 115v and 230v mains supplies
- Dual rectified power amp supplies for reduced ground noise
- All gold plated input / output connectors
- Size – 430mm (17") wide, 370mm (14") deep, 110mm (4.2") high
- Weight 12.5kg
-----SOLD-----
CARY CAD 300SE MONOBLOCKS
MADE IN USA
Specifications :
Circuit Type Single-Ended Class A
Power Output 15 watts
Input Sensitivity 1.5 Volt for full output
Noise and Hum -80 dB below full output
Frequency Response 20 Hz to 20 KHz +/- 0.75 dB
AC Power Requirements 120/240 VAC @ 50/60 Hz
Consumption 125 watts - Normal Operation
50 watts - Stand By
Net Weight 32 lbs each
Dimensions 7" H x 5.5" W x 19" D
------SOLD-------
MADE IN USA
Specifications :
Circuit Type Single-Ended Class A
Power Output 15 watts
Input Sensitivity 1.5 Volt for full output
Noise and Hum -80 dB below full output
Frequency Response 20 Hz to 20 KHz +/- 0.75 dB
AC Power Requirements 120/240 VAC @ 50/60 Hz
Consumption 125 watts - Normal Operation
50 watts - Stand By
Net Weight 32 lbs each
Dimensions 7" H x 5.5" W x 19" D
------SOLD-------
AUDIO ANALOQUE
DONIZETTI CENTO
MADE IN ITALY
Donizetti Cento is a 100 Watt per channel amplifier with single-ended and balanced inputs, trigger input and output, high-performance circuits and separated circuit sections for each channel.Donizetti Cento solutions make the unit a valuable and durable investment. Analog power supply with a separated toroidal transformer and line for each channel, separated power supply for the trigger out. Large bandwidth and low feedback circuitry. High-quality unbalancer for the best connection to preamplifiers with balanced output. Low IMD, high slew rate power section. Calibrated and integrated electronic protections for electric overloads prevention to minimize sound distortion. Single-ended/balanced input selector located on the rear panel next to the input connectors. High-quality passive components.
------SOLD------
DONIZETTI CENTO
MADE IN ITALY
Donizetti Cento is a 100 Watt per channel amplifier with single-ended and balanced inputs, trigger input and output, high-performance circuits and separated circuit sections for each channel.Donizetti Cento solutions make the unit a valuable and durable investment. Analog power supply with a separated toroidal transformer and line for each channel, separated power supply for the trigger out. Large bandwidth and low feedback circuitry. High-quality unbalancer for the best connection to preamplifiers with balanced output. Low IMD, high slew rate power section. Calibrated and integrated electronic protections for electric overloads prevention to minimize sound distortion. Single-ended/balanced input selector located on the rear panel next to the input connectors. High-quality passive components.
------SOLD------
Power Amplifier (Tube)
AUDIO RESEARCH VS110
MADE IN USA
Specifications:
POWER OUTPUT: 100 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 100 watts, below .05% at 1 watt. Approximate actual power available at "clipping" 120 watts (1kHz). (Note that actual power output is dependent upon both line voltage and "condition" i. e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
POWER BANDWIDTH: (-3dB points) 10Hz to 40kHz.
FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.8 Hz to 40 kHz.
INPUT SENSITIVITY: 1.1V RMS Single-ended for rated output. (28dB gain into 8 ohms.)
INPUT IMPEDANCE: 100K ohms Single-ended.
OUTPUT TAPS: 8 ohms, 4 ohms.
OUTPUT REGULATION: Approximately 0.9dB 8 ohm load to open circuit (Damping factor approximately 11).
OVERALL NEGATIVE FEEDBACK: 12.7dB.
SLEW RATE: 6 volts/microsecond.
RISE TIME: 10 microseconds.
HUM & NOISE: Less than 0.2mV RMS - 103dB below rated output (IHF weighted, input shorted).
POWER SUPPLY ENERGY STORAGE: Approximately 332 joules.
POWER REQUIREMENTS: 105-125VAC 60Hz (210-250VAC 50Hz) 620 watts at rated output, 900 watts maximum, 400 watts at "idle".
TUBES REQUIRED: 4 - Matched pair 6550C - Power Output; 5 - 6N1P input and driver.
DIMENSIONS : 17.5" (44.5 cm) W x 7.9" (20.1 cm) H x 19" (48.3 cm) D. Rear connectors extend .88" beyond chassis.
WEIGHT: 61 lbs. (27.7 kg) Net; 69 lbs. (31.4 kg) Shipping.
-----SOLD------
MADE IN USA
Specifications:
POWER OUTPUT: 100 watts per channel continuous from 20Hz to 20kHz. 1kHz total harmonic distortion typically 0.5% at 100 watts, below .05% at 1 watt. Approximate actual power available at "clipping" 120 watts (1kHz). (Note that actual power output is dependent upon both line voltage and "condition" i. e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
POWER BANDWIDTH: (-3dB points) 10Hz to 40kHz.
FREQUENCY RESPONSE: (-3dB points at 1 watt) 0.8 Hz to 40 kHz.
INPUT SENSITIVITY: 1.1V RMS Single-ended for rated output. (28dB gain into 8 ohms.)
INPUT IMPEDANCE: 100K ohms Single-ended.
OUTPUT TAPS: 8 ohms, 4 ohms.
OUTPUT REGULATION: Approximately 0.9dB 8 ohm load to open circuit (Damping factor approximately 11).
OVERALL NEGATIVE FEEDBACK: 12.7dB.
SLEW RATE: 6 volts/microsecond.
RISE TIME: 10 microseconds.
HUM & NOISE: Less than 0.2mV RMS - 103dB below rated output (IHF weighted, input shorted).
POWER SUPPLY ENERGY STORAGE: Approximately 332 joules.
POWER REQUIREMENTS: 105-125VAC 60Hz (210-250VAC 50Hz) 620 watts at rated output, 900 watts maximum, 400 watts at "idle".
TUBES REQUIRED: 4 - Matched pair 6550C - Power Output; 5 - 6N1P input and driver.
DIMENSIONS : 17.5" (44.5 cm) W x 7.9" (20.1 cm) H x 19" (48.3 cm) D. Rear connectors extend .88" beyond chassis.
WEIGHT: 61 lbs. (27.7 kg) Net; 69 lbs. (31.4 kg) Shipping.
-----SOLD------
Power Amplifier
KRELL KSA-50S
MADE IN USA
The KSA-50S is the smallest member of Krell's "Sustained Plateau Biasing" range of power amplifiers, launched in 1993. The amplifier's rear panel has one pair of brass binding posts against the bigger amplifiers' two pairs. Input sockets are XLRs (balanced) and RCAs (unbalanced). When the amp is used unbalanced, Krell recommends shunting the "cold-polarity" XLR pins to ground with the supplied jumpers to avoid excessive noise pickup. The KSA-50S is specified at 50Wpc into 8 ohms.
------SOLD-------
MADE IN USA
The KSA-50S is the smallest member of Krell's "Sustained Plateau Biasing" range of power amplifiers, launched in 1993. The amplifier's rear panel has one pair of brass binding posts against the bigger amplifiers' two pairs. Input sockets are XLRs (balanced) and RCAs (unbalanced). When the amp is used unbalanced, Krell recommends shunting the "cold-polarity" XLR pins to ground with the supplied jumpers to avoid excessive noise pickup. The KSA-50S is specified at 50Wpc into 8 ohms.
------SOLD-------
Power Amplifier
MOON W5 LIMITED EDITION
MADE IN CANADA
The MOON W-5 LE balanced differential Dual-mono Power Amplifier produces 200 watts/channel into 8 ohms and 400 watts/channel into 4 ohms. As well, it can be easily configured for mono operation.
Unique to the LE version of the MOON W-5 are enhanced gain and output sections. The power output has been increased to 200W/ch. This, along with exotic parts in critical areas allows for an even higher level of musical speed and transparency. The awesome dynamic range and effortless immunity to any known load is better than ever in the W-5 LE.
MOON Limited Edition series features include polished chrome accents, a ½" thick brushed & anodized silver faceplate, a custom 2 meter Cardas power cord and a Limited Edition serial number plaque. Beginning in January 2004, Simaudio Ltd. producing only 250 units of the MOON W-5 LE with the retail price of $6000
------SOLD------
MADE IN CANADA
The MOON W-5 LE balanced differential Dual-mono Power Amplifier produces 200 watts/channel into 8 ohms and 400 watts/channel into 4 ohms. As well, it can be easily configured for mono operation.
Unique to the LE version of the MOON W-5 are enhanced gain and output sections. The power output has been increased to 200W/ch. This, along with exotic parts in critical areas allows for an even higher level of musical speed and transparency. The awesome dynamic range and effortless immunity to any known load is better than ever in the W-5 LE.
MOON Limited Edition series features include polished chrome accents, a ½" thick brushed & anodized silver faceplate, a custom 2 meter Cardas power cord and a Limited Edition serial number plaque. Beginning in January 2004, Simaudio Ltd. producing only 250 units of the MOON W-5 LE with the retail price of $6000
------SOLD------
Power Amplifier
NAD SILVERLINE S200
MADE IN UK
Key Features
Output Power : 500 watt
Amplifier Output Details : 225 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.03% - 2 channel(s) ( front ), 700 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.03% - 1 channel(s)
Response Bandwidth : 2 - 100000 Hz
Input Impedance : 47 kOhm
Input Sensitivity : 1.4 V
Dimensions :
Height 7.09 in.
Width 17.72 in.
------SOLD------
MADE IN UK
Key Features
Output Power : 500 watt
Amplifier Output Details : 225 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.03% - 2 channel(s) ( front ), 700 Watt - 8 Ohm - 20 - 20000 Hz - THD 0.03% - 1 channel(s)
Response Bandwidth : 2 - 100000 Hz
Input Impedance : 47 kOhm
Input Sensitivity : 1.4 V
Dimensions :
Height 7.09 in.
Width 17.72 in.
------SOLD------
Power Amplifier (Tube)
MANLEY MAHI-MAHI
MONOBLOCKS
MADE IN USA
Specifications :
Output Power: 40 Watts
Vacuum Tubes: four EL84 for output, one 12AT7WA for input, and one 6414 as driver
Frequency Response: 10Hz to 90kHz (+0.5dB)
Input Sensitivity: 460 mV nominal
Input Impedance: 100 kohms
Load Impedance: 5 ohms
S/N Ratio at 50 Watts: -80dB
Dynamic Range: 86dB
Dimensions: 12 x 10 x 5 (WxDxH in inches)
Shipping Weight: 17 lbs. each
----SOLD-----
MONOBLOCKS
MADE IN USA
Specifications :
Output Power: 40 Watts
Vacuum Tubes: four EL84 for output, one 12AT7WA for input, and one 6414 as driver
Frequency Response: 10Hz to 90kHz (+0.5dB)
Input Sensitivity: 460 mV nominal
Input Impedance: 100 kohms
Load Impedance: 5 ohms
S/N Ratio at 50 Watts: -80dB
Dynamic Range: 86dB
Dimensions: 12 x 10 x 5 (WxDxH in inches)
Shipping Weight: 17 lbs. each
----SOLD-----
Power Amplifier
SUMO THE NINE PLUS
MADE IN USA
MADE IN USA
- Power output: 65 watts per channel into 8Ω (stereo)
Frequency response: 2Hz to 120kHz
Total harmonic distortion: 0.25%
Damping factor: 120
Input sensitivity: 1V
Signal to noise ratio: 100dB
Dimensions: 480 x 220 x 180mm
Weight: 16kg
-----SOLD-----
VTL ST-150
MADE IN USA
Specifications :
Vacuum Tube Complement : 8 x 6550, 2 x 12AT7, 2 x 12BH7
Output power : Tetrode: 120W, Triode: 60W
Input sensitivity @ 150W
input impedance 130KΩ
Output Load Range 2Ω – 8Ω
S/N Ratio -95dB, 120Hz
Power Consumption Idle = 240W, Full Power = 800W
Dimensions W x D x H : 19 x 12 x 9 inches (48 x 30 x 23 cm)
Weight : 85lbs (38.6Kg), 110lb (50Kg) packed
-----SOLD------
MADE IN USA
Specifications :
Vacuum Tube Complement : 8 x 6550, 2 x 12AT7, 2 x 12BH7
Output power : Tetrode: 120W, Triode: 60W
Input sensitivity @ 150W
input impedance 130KΩ
Output Load Range 2Ω – 8Ω
S/N Ratio -95dB, 120Hz
Power Consumption Idle = 240W, Full Power = 800W
Dimensions W x D x H : 19 x 12 x 9 inches (48 x 30 x 23 cm)
Weight : 85lbs (38.6Kg), 110lb (50Kg) packed
-----SOLD------
Power Amplifier
ADCOM GFA-585 Limited Edition
MADE IN USA
Specifications :
Power output: 250 watts per channel into 8Ω (stereo)
Frequency response: 10Hz to 20kHz
Total harmonic distortion: 0.02%
Damping factor: 600
Gain: 27 dB
Input sensitivity: 2V
Signal to noise ratio: 110dB
Semiconductors: 72 x transistors, 11 x zener diodes, 31 x diodes, 2 x IC, 2 x diode bridges
Dimensions: 213 x 432 x 310mm
Weight: 20.5kg
-----SOLD-------
MADE IN USA
Specifications :
Power output: 250 watts per channel into 8Ω (stereo)
Frequency response: 10Hz to 20kHz
Total harmonic distortion: 0.02%
Damping factor: 600
Gain: 27 dB
Input sensitivity: 2V
Signal to noise ratio: 110dB
Semiconductors: 72 x transistors, 11 x zener diodes, 31 x diodes, 2 x IC, 2 x diode bridges
Dimensions: 213 x 432 x 310mm
Weight: 20.5kg
-----SOLD-------
Power Amplifier (Tube)
CARY CAD300B
MADE IN USA
Tube Power Amplifier Cary CAD-300B Push-Pull 2x20 wpc
------SOLD------
MADE IN USA
Tube Power Amplifier Cary CAD-300B Push-Pull 2x20 wpc
------SOLD------
PASS LABS ALEPH 3
MADE IN USA
Description: Stereo power amplifier with single-ended, class-A output stage. Power output: 30W into 8 ohms (14.8dBW), 60W into 4 or 2 ohms (14.8dBW, 11.8dBW, respectively). Frequency response: 2Hz-100kHz, -0.5dB. Input impedance: 23k ohms. Voltage Gain: 20dB. Output impedance: 0.08 ohms. 1kHz distortion: 0.2% at 30W (8 ohms), 1% at 60W (4 or 2 ohms). DC offset: ±100mV. Power consumption: 250W at all times.
Dimensions: 12" W by 6" H by 12" D. Shipping weight: 38 lbs.
-----SOLD-----
MADE IN USA
Description: Stereo power amplifier with single-ended, class-A output stage. Power output: 30W into 8 ohms (14.8dBW), 60W into 4 or 2 ohms (14.8dBW, 11.8dBW, respectively). Frequency response: 2Hz-100kHz, -0.5dB. Input impedance: 23k ohms. Voltage Gain: 20dB. Output impedance: 0.08 ohms. 1kHz distortion: 0.2% at 30W (8 ohms), 1% at 60W (4 or 2 ohms). DC offset: ±100mV. Power consumption: 250W at all times.
Dimensions: 12" W by 6" H by 12" D. Shipping weight: 38 lbs.
-----SOLD-----
Power Amplifier
MC CORMACK DNA-1
MADE IN USA
Technical Specifications
-----SOLD------
MADE IN USA
Technical Specifications
- Output Power at Clipping, both channels driven RMS Watts per channel: 185 Watts @ 8 ohms, 370 Watts @ 4 ohms, 600 Watts @ 2 ohms
- Output Current: 50 Amps peak, per channel
- Input Impedance: 100K ohms
- Input Sensitivity: 1 Vrms
- Frequency Response: -3db @ 0.5 Hz, 250 KHz
- Risetime: <2 micro seconds
- Slew Rate: 50V/micro second
- Signal-to-Noise: 88dB, "A" weighted
- Damping Factor (1 KHz, 8 ohm load): >100
- Output Impedance: <0.1 ohm
- DC Offset (Servo-controlled): <5mV
- Signal Polarity ("Absolute Phase"): Non-inverting
- Power Requirements: 100-117 VAC/60 Hz, 1.2 Amps/130 Watts @ idle, 3.5 Amps/400 Watts @ clipping
- Power Requirements: 220-240 VAC/50 Hz, .6 Amps/130 Watts @ idle, 1.8 Amps/400 Watts @ clipping
- Dimensions: 19" wide, 7" high, 15" deep
- Shipping weight: 55 lbs.
-----SOLD------
Power Amplifier
KRELL FPB300
MADE IN USA
Specifications:
Frequency Response ~20 Hz to 20 kHz +0 dB, -0.05 dB ~0.1 Hz to 240 kHz +0 dB, -3 dB
Signal to Noise Ratio ”A” Weighted 117 dB Gain 26.4dB
Total Harmonic Distortion All Balanced, Unweigted 1 kHz <0.02% 20 kHz <0.15%
Input Impedance 100 kOhms
Input Sensitivity 2.35 Vrms
Output Power Each Channel Driven 8 Ohms 300 W 4 Ohms 600 W 2 Ohms 1,200 W
Output Voltage Peak to Peak 170 V RMS 60 V
Power Consumption Stand-by 75 W Idle 350 W Max. 3,000 W
Dimensions Amp: 19” W x 10 ¼” H x 21” D
-----SOLD-----
MADE IN USA
Specifications:
Frequency Response ~20 Hz to 20 kHz +0 dB, -0.05 dB ~0.1 Hz to 240 kHz +0 dB, -3 dB
Signal to Noise Ratio ”A” Weighted 117 dB Gain 26.4dB
Total Harmonic Distortion All Balanced, Unweigted 1 kHz <0.02% 20 kHz <0.15%
Input Impedance 100 kOhms
Input Sensitivity 2.35 Vrms
Output Power Each Channel Driven 8 Ohms 300 W 4 Ohms 600 W 2 Ohms 1,200 W
Output Voltage Peak to Peak 170 V RMS 60 V
Power Consumption Stand-by 75 W Idle 350 W Max. 3,000 W
Dimensions Amp: 19” W x 10 ¼” H x 21” D
-----SOLD-----
Power Amplifier
THRESHOLD S/150
MADE IN USA
The Threshold S/150 is 75watts per/ch, class A/B.
-----SOLD----
MADE IN USA
The Threshold S/150 is 75watts per/ch, class A/B.
-----SOLD----
MCINTOSH MC7200
MADE IN USA
SPECIFICATIONS:
200w/ch into 8ohms.300w into 4ohms. (600w into 8ohms mono).
Response: 20-20kHz(+0-0.25dB).
Distortion 0.005%.
Noise and Hum: 105dBA.
Output: Direct couple for4 to 8ohms.
DampingFactor: 200 or greater.
Input Impedance: 20k unbalanced,40k balanced.
InputSensitivity: 1.4v or 2.5v
----SOLD----
MADE IN USA
SPECIFICATIONS:
200w/ch into 8ohms.300w into 4ohms. (600w into 8ohms mono).
Response: 20-20kHz(+0-0.25dB).
Distortion 0.005%.
Noise and Hum: 105dBA.
Output: Direct couple for4 to 8ohms.
DampingFactor: 200 or greater.
Input Impedance: 20k unbalanced,40k balanced.
InputSensitivity: 1.4v or 2.5v
----SOLD----
Power Amplifier
THRESHOLD S/500
MADE IN USA
The Threshold S/500 Stasis Power Amplifier Solid-state stereo amplifier. 250 watts/channel, max. current 22 amp. Frequency response I to 100k Hz, +0/-3 dB. Damping factor 100 from 20 to 20kHz. Slew rate 80V/usec. Dimen-sions 19" W by 19" D by 9-1/2" H, overall. Weight 92 lbs
-----SOLD----
MADE IN USA
The Threshold S/500 Stasis Power Amplifier Solid-state stereo amplifier. 250 watts/channel, max. current 22 amp. Frequency response I to 100k Hz, +0/-3 dB. Damping factor 100 from 20 to 20kHz. Slew rate 80V/usec. Dimen-sions 19" W by 19" D by 9-1/2" H, overall. Weight 92 lbs
-----SOLD----
Power Amplifier (Tube)
VENTURE REFERENCE ONE
MADE IN BELGIUM
Output Power: 2 x 25 Watts. Input sensitivity: 400 mV. Input Impedance: 1 M Ohm. Power Bandwidth: 8 - 50000 Hz. Bias: external adjustable.
-----SOLD-----
MADE IN BELGIUM
Output Power: 2 x 25 Watts. Input sensitivity: 400 mV. Input Impedance: 1 M Ohm. Power Bandwidth: 8 - 50000 Hz. Bias: external adjustable.
-----SOLD-----
Power Amplifier
USHER REFERENCE 1.5
MADE IN TAIWAN
Description
The R-1.5 amplifier is designed to drive any loudspeaker, producing warm, "tube like" sound quality. It has been constructed with premium parts, including metal film resistors and film capacitors, reinforcing Usher's reputation for high-quality manufacturing. High-power bipolar transistors, designed by Motorola, can handle sophisticated power and current requirements. And its massive AC power transformer works with a high-capacitive filtering system for the purest sound. Other features include Burrow-Brown OPA2134P Sond Plus Series op amps, bridging switch for mono block operation, terminals that accept both banana plugs and spades, optional balanced inputs and large handles on the front and rear panel.
8 Ohm/20Hz-20kHz: 150W(ch)
4 Ohm/20Hz-20kHz: 260W(ch)
Damping factor: >175 (single ended)
Circumgyration: >40V / uS
Power supply (4 Ohm): >16A
Transient power supply: >75A
S/N ratio: 100 dB
Frequency (20Hz-20kHz): +/-0.1dB
Shipping weight 87 lbs/pc
----SOLD----
MADE IN TAIWAN
Description
The R-1.5 amplifier is designed to drive any loudspeaker, producing warm, "tube like" sound quality. It has been constructed with premium parts, including metal film resistors and film capacitors, reinforcing Usher's reputation for high-quality manufacturing. High-power bipolar transistors, designed by Motorola, can handle sophisticated power and current requirements. And its massive AC power transformer works with a high-capacitive filtering system for the purest sound. Other features include Burrow-Brown OPA2134P Sond Plus Series op amps, bridging switch for mono block operation, terminals that accept both banana plugs and spades, optional balanced inputs and large handles on the front and rear panel.
8 Ohm/20Hz-20kHz: 150W(ch)
4 Ohm/20Hz-20kHz: 260W(ch)
Damping factor: >175 (single ended)
Circumgyration: >40V / uS
Power supply (4 Ohm): >16A
Transient power supply: >75A
S/N ratio: 100 dB
Frequency (20Hz-20kHz): +/-0.1dB
Shipping weight 87 lbs/pc
----SOLD----
Power Amplifier
MARK LEVINSON NO.331
MADE IN USA
Description: Solid-state stereo amplifier. Rated output power, 20Hz–20kHz, with no more than 0.5% THD (FTC): 100Wpc minimum continuous into 8 ohms (20dBW); 200Wpc minimum continuous into 4 ohms (20dBW); 400Wpc continuous into 2 ohms (20dBW). Peak output voltage at rated line voltage: 48V into 8 ohms. Frequency response: 20Hz–20kHz ±1dB. S/N ratio (main output): <–80dB (ref. 1W). Input impedance: 100k ohms balanced, 50k ohms single-ended. Voltage gain: 26.8dB. Input sensitivity (for 2.8V output): 130mV. Input sensitivity (for full output): 1.3V. Output impedance: !x0.05 ohms, 20Hz–20kHz. Damping factor: >800, 20Hz–20kHz into 8 ohms. Power consumption: typically 260W at idle, 110W in standby.
Dimensions: 17.56" (446mm) W by 18.85" (479mm) D by 9.3" (232mm) H; faceplate curve depth 1.22" (31mm). Shipping weight: 112 lbs.
------SOLD----
MADE IN USA
Description: Solid-state stereo amplifier. Rated output power, 20Hz–20kHz, with no more than 0.5% THD (FTC): 100Wpc minimum continuous into 8 ohms (20dBW); 200Wpc minimum continuous into 4 ohms (20dBW); 400Wpc continuous into 2 ohms (20dBW). Peak output voltage at rated line voltage: 48V into 8 ohms. Frequency response: 20Hz–20kHz ±1dB. S/N ratio (main output): <–80dB (ref. 1W). Input impedance: 100k ohms balanced, 50k ohms single-ended. Voltage gain: 26.8dB. Input sensitivity (for 2.8V output): 130mV. Input sensitivity (for full output): 1.3V. Output impedance: !x0.05 ohms, 20Hz–20kHz. Damping factor: >800, 20Hz–20kHz into 8 ohms. Power consumption: typically 260W at idle, 110W in standby.
Dimensions: 17.56" (446mm) W by 18.85" (479mm) D by 9.3" (232mm) H; faceplate curve depth 1.22" (31mm). Shipping weight: 112 lbs.
------SOLD----
Power Amplifier
CLASSE FIFTEEN
MADE IN CANADA
Description: Solid-state stereo power amplifier. Rated output power (20Hz–20kHz): 175Wpc minimum continuous sinewave power into 8 ohms (22.4dBW), with no more than 0.1% THD (FTC); 375Wpc minimum continuous sinewave power into 4 ohms (22.7dBW), with no more than 0.3% THD (FTC); bridged-mono, 700W continuous sinewave power into 8 ohms (28.5dBW), 1200W mono into 4 ohms (27.8dBW). Frequency response: 20Hz–20kHz ±0.1dB. Input impedance: 70k ohms. Voltage gain: not specified. Power consumption: typically 225W at idle.
Dimensions:17.25" (431.25mm) W by 7.25" (181.25mm) H by 19" (475mm) D. Shipping weight: 60 lbs (27kg).
-----SOLD------
MADE IN CANADA
Description: Solid-state stereo power amplifier. Rated output power (20Hz–20kHz): 175Wpc minimum continuous sinewave power into 8 ohms (22.4dBW), with no more than 0.1% THD (FTC); 375Wpc minimum continuous sinewave power into 4 ohms (22.7dBW), with no more than 0.3% THD (FTC); bridged-mono, 700W continuous sinewave power into 8 ohms (28.5dBW), 1200W mono into 4 ohms (27.8dBW). Frequency response: 20Hz–20kHz ±0.1dB. Input impedance: 70k ohms. Voltage gain: not specified. Power consumption: typically 225W at idle.
Dimensions:17.25" (431.25mm) W by 7.25" (181.25mm) H by 19" (475mm) D. Shipping weight: 60 lbs (27kg).
-----SOLD------
Power Amplifier
ROKSAN CASPIAN
MADE IN ENGLAND
This 85 watts / channel stereo power amplifier is built to the same rigorous standards as the Caspian mono-block with the same attention to detail and clarity of sound quality. It is designed for multi-amping with the Caspian integrated amplifier or to be partnered with the Caspian pre amplifier. The Caspian M-series stereo is built using superior quality components used in the Caspian mono block and the power section of the Caspian Integrated amplifier. Precise timing, enhanced sound staging and excellent loudspeaker control have aided to redefine the performance of this world reference amplifier. Complete with its new yet classic timeless aesthetics, the Caspian M series stereo is an amplifier in a class of its own.
Technical Data
· Input Impedance 38 kΩ
· Input Sensitivity 700mV RMS
· Signal Inputs Left & Right channels
· Signal Outputs Chain Output L & R Channels
· Power Outputs Loudspeaker, L & R
· Output Power >85 Watts continuous, into 8Ω, both channels driven
· >120 Watts continuous, into 4Ω, both channels driven
· Power Supply 330VA Ultra Low Noise Toroidal Transformer
· Current Output 50 Amps Peak to Peak
· Damping Factor >140 (8Ω)
· Frequency response -3dB, <1Hz – >100kHz
· Gain 30.7dB
-----SOLD-----
MADE IN ENGLAND
This 85 watts / channel stereo power amplifier is built to the same rigorous standards as the Caspian mono-block with the same attention to detail and clarity of sound quality. It is designed for multi-amping with the Caspian integrated amplifier or to be partnered with the Caspian pre amplifier. The Caspian M-series stereo is built using superior quality components used in the Caspian mono block and the power section of the Caspian Integrated amplifier. Precise timing, enhanced sound staging and excellent loudspeaker control have aided to redefine the performance of this world reference amplifier. Complete with its new yet classic timeless aesthetics, the Caspian M series stereo is an amplifier in a class of its own.
Technical Data
· Input Impedance 38 kΩ
· Input Sensitivity 700mV RMS
· Signal Inputs Left & Right channels
· Signal Outputs Chain Output L & R Channels
· Power Outputs Loudspeaker, L & R
· Output Power >85 Watts continuous, into 8Ω, both channels driven
· >120 Watts continuous, into 4Ω, both channels driven
· Power Supply 330VA Ultra Low Noise Toroidal Transformer
· Current Output 50 Amps Peak to Peak
· Damping Factor >140 (8Ω)
· Frequency response -3dB, <1Hz – >100kHz
· Gain 30.7dB
-----SOLD-----
Power Amplifier (Tube)
VTL ST-85
MADE IN USA
Description: Tube stereo power amplifier. Tube complement: four EL34, four 12AT7. Inputs: One gold-plated RCA jack per channel. Outputs: 1 pair solid-metal gold-plated four-way speaker terminals per channel. Maximum power output: 85Wpc into 4 ohms, 20Hz-20kHz (13.3dBW). THD at rated output: <3%, 20Hz-20kHz. S/N ratio: 95dB at 120Hz. Input sensitivity: 1.1V for full output. Input impedance: 100k ohms. Output impedance: 0.9 ohms. Recommended load impedance: 3-8 ohms. Power consumption: idle, 175W; full power, 550W.
Dimensions: 15.75" W by 6.75" H by 12" D. Weight: 38 lbs net, 43 lbs shipping.
----SOLD---
MADE IN USA
Description: Tube stereo power amplifier. Tube complement: four EL34, four 12AT7. Inputs: One gold-plated RCA jack per channel. Outputs: 1 pair solid-metal gold-plated four-way speaker terminals per channel. Maximum power output: 85Wpc into 4 ohms, 20Hz-20kHz (13.3dBW). THD at rated output: <3%, 20Hz-20kHz. S/N ratio: 95dB at 120Hz. Input sensitivity: 1.1V for full output. Input impedance: 100k ohms. Output impedance: 0.9 ohms. Recommended load impedance: 3-8 ohms. Power consumption: idle, 175W; full power, 550W.
Dimensions: 15.75" W by 6.75" H by 12" D. Weight: 38 lbs net, 43 lbs shipping.
----SOLD---
Power Amplifier
FM ACOUSTICS 800A
SERIES II
MADE IN SWITZERLAND
Specifications :
Number of Channels 2
Rated Slew Rate, V/µS 25
High-Level Sensitivity, mV .6v
Does Amp Invert Polarity? No
Continous Average Watts/Channel into 8 Ohms 400
Continous Average Watts/Channel into 4 Ohms 600
Rated THD, % 0.007
Rated Full-Power Bandwidth, Hz to KHZ 5-60
Class of Output Operation A
Input Impedance, Kilohms 5
Weight, Pounds (To Nearest Pound) 66
-----SOLD---
SERIES II
MADE IN SWITZERLAND
Specifications :
Number of Channels 2
Rated Slew Rate, V/µS 25
High-Level Sensitivity, mV .6v
Does Amp Invert Polarity? No
Continous Average Watts/Channel into 8 Ohms 400
Continous Average Watts/Channel into 4 Ohms 600
Rated THD, % 0.007
Rated Full-Power Bandwidth, Hz to KHZ 5-60
Class of Output Operation A
Input Impedance, Kilohms 5
Weight, Pounds (To Nearest Pound) 66
-----SOLD---
Power Amplifier (Tube)
STRATOSPHERE STR-1008
MADE IN CANADA
TECHNICAL SPECIFICATIONS
Output Power : 110W
Frequency responsible at 1 W 10 Hz - 100Khz
Distortion at 1W < 0.1%
Distortion at full power < 3%
Frequency responsible at full power 18Hz - 28Khz
S/N Ratio / Noise level mV 80 db /3mV
S/N Ratio with A weighting 97 db (0.4mV)
Input impedance 100K
Output Impedance 4,8,16 Ohm
Input sensitive 1V
Power request 335W
Fuse 5A Slow blow
Power cord - Detachable /Fixed Detachable
Input Sockets RCA Gold Plate
Output terminal Heavy duty gold plate 5 ways speaker post
Chassis Finish Polished Steel
Front Panel Finish Aluminum with Anodizing Gold
Tube Complement 6550/KT88 x 4, 6SN7 x 2
Dimension W x D x H in mm 260 x 395 x 220
Shipping Dimension W x D x H in mm 350 x 470 x 315
Net Weight /Kg 19Kg
Shipping Weight /Kg 20Kg
------SOLD----
MADE IN CANADA
TECHNICAL SPECIFICATIONS
Output Power : 110W
Frequency responsible at 1 W 10 Hz - 100Khz
Distortion at 1W < 0.1%
Distortion at full power < 3%
Frequency responsible at full power 18Hz - 28Khz
S/N Ratio / Noise level mV 80 db /3mV
S/N Ratio with A weighting 97 db (0.4mV)
Input impedance 100K
Output Impedance 4,8,16 Ohm
Input sensitive 1V
Power request 335W
Fuse 5A Slow blow
Power cord - Detachable /Fixed Detachable
Input Sockets RCA Gold Plate
Output terminal Heavy duty gold plate 5 ways speaker post
Chassis Finish Polished Steel
Front Panel Finish Aluminum with Anodizing Gold
Tube Complement 6550/KT88 x 4, 6SN7 x 2
Dimension W x D x H in mm 260 x 395 x 220
Shipping Dimension W x D x H in mm 350 x 470 x 315
Net Weight /Kg 19Kg
Shipping Weight /Kg 20Kg
------SOLD----
Power Amplifier (Tube)
CANARY CA-300 MONOBLOCK
MADE IN USA
Specification :
Model: CA-300
Rated Power Output: 8 Watts RMS
Input Sensitivity: 1.2 Volts for full output
Input Impedance: 100,000 Ohms
Frequency Response: +/- 3 dB from 10 Hz to 54,000 Hz
Total Harmonic: < 0.3%
Signal-to-Noise ratio: -84 dB below 1 Watt
Damping Factor: 3
Power Consumption: 100 Watts (true RMS)
Output Impedance: 4, 8 Ohm
Tube Complement (per channel): 1-300B, 1-6SL7GTB, 1-5U4GB
Dimensions (per channel): 8” W x 18” D x 7” H
Weight (per channel): 33 lbs.
----SOLD---
MADE IN USA
Specification :
Model: CA-300
Rated Power Output: 8 Watts RMS
Input Sensitivity: 1.2 Volts for full output
Input Impedance: 100,000 Ohms
Frequency Response: +/- 3 dB from 10 Hz to 54,000 Hz
Total Harmonic: < 0.3%
Signal-to-Noise ratio: -84 dB below 1 Watt
Damping Factor: 3
Power Consumption: 100 Watts (true RMS)
Output Impedance: 4, 8 Ohm
Tube Complement (per channel): 1-300B, 1-6SL7GTB, 1-5U4GB
Dimensions (per channel): 8” W x 18” D x 7” H
Weight (per channel): 33 lbs.
----SOLD---
Power Amplifier
PERREAUX 250P
MADE IN NEW ZEALAND
The PERREAUX 250 is a high quality reference dual channel 250 watt power amplifier incorporating dual mono power supply topology and balanced input circuitry.
Power output : 250 watts per channel
Inputs : Balanced and unbalanced
Dimensions : 482mm W x 195mm H x 520mm D
Colour : Black
1 x Dual RCA Inputs
1 x Dual Balanced Inputs
2 x Parallelled Output Terminals Per Channel
Features
Dual Power Supplies
Mos-Fet Output Stage
Very High Power Output & Current Capability
Multiple Protection Systems
Driver Stages Running In Class A - Output Stage Running In Sliding
Class A/B
Soft Start Providing Delayed Power On and Instant Off
----SOLD---
MADE IN NEW ZEALAND
The PERREAUX 250 is a high quality reference dual channel 250 watt power amplifier incorporating dual mono power supply topology and balanced input circuitry.
Power output : 250 watts per channel
Inputs : Balanced and unbalanced
Dimensions : 482mm W x 195mm H x 520mm D
Colour : Black
1 x Dual RCA Inputs
1 x Dual Balanced Inputs
2 x Parallelled Output Terminals Per Channel
Features
Dual Power Supplies
Mos-Fet Output Stage
Very High Power Output & Current Capability
Multiple Protection Systems
Driver Stages Running In Class A - Output Stage Running In Sliding
Class A/B
Soft Start Providing Delayed Power On and Instant Off
----SOLD---
Power Amplifier (Tube)
AUDIO RESEARCH
VT100
MADE IN USA
SPECIFICATIONS :
Power output 100 watts per channel continuous from 20Hz to 20kHz. Approximate actual power available at "clipping" 110 watts (1kHz) ;
Power bandwidth (-3dB points) 15Hz to 80kHz ;
Frequency response (-3dB points at 1 watt) 1Hz to 100 kHz ;
Input sensitivity 1.9V RMS (Bal or SE) for rated output. (23.5 dB gain into 8 ohms.) ;
Input impedance 200K ohms Balanced, 100K ohms Single-ended. ;
Output taps 8 ohms, 4 ohms ;
Output regulation Approximately 0.8dB 8 ohm load to open circuit ;
Overall negative feedback 10 dB ;
Damping factor 11 ;
Distortion 1kHz total harmonic distortion typically 1% at 100 watts, below .05% at 1 watt ;
Slew rate 15 Volts/µs ;
Rise time 3 µs ;
Hum & noise Less than 0.5mV RMS 95dB below rated output (IHF weighted, input shorted) ;
Power supply energy storage VT100: 270 joules ;
Power requirements 105-125VAC 60Hz (210-250VAC 50Hz) 585 watts at rated output, 50 watts maximum, 380 watts at "idle" ;
Tube complement VT100: (4 matched pairs) 6550 power output, (8) 6922 ;
Dimensions 19" (48.3 cm) W x 8.75" (22.2 cm) H x 19.5" (49.5 cm) D. Handles extend 1.5" (3.8 cm) forward ;
Weight 65 lbs. (29.5 kg) Net; 83 lbs. (37.7 kg) Shipping.
----SOLD----
VT100
MADE IN USA
SPECIFICATIONS :
Power output 100 watts per channel continuous from 20Hz to 20kHz. Approximate actual power available at "clipping" 110 watts (1kHz) ;
Power bandwidth (-3dB points) 15Hz to 80kHz ;
Frequency response (-3dB points at 1 watt) 1Hz to 100 kHz ;
Input sensitivity 1.9V RMS (Bal or SE) for rated output. (23.5 dB gain into 8 ohms.) ;
Input impedance 200K ohms Balanced, 100K ohms Single-ended. ;
Output taps 8 ohms, 4 ohms ;
Output regulation Approximately 0.8dB 8 ohm load to open circuit ;
Overall negative feedback 10 dB ;
Damping factor 11 ;
Distortion 1kHz total harmonic distortion typically 1% at 100 watts, below .05% at 1 watt ;
Slew rate 15 Volts/µs ;
Rise time 3 µs ;
Hum & noise Less than 0.5mV RMS 95dB below rated output (IHF weighted, input shorted) ;
Power supply energy storage VT100: 270 joules ;
Power requirements 105-125VAC 60Hz (210-250VAC 50Hz) 585 watts at rated output, 50 watts maximum, 380 watts at "idle" ;
Tube complement VT100: (4 matched pairs) 6550 power output, (8) 6922 ;
Dimensions 19" (48.3 cm) W x 8.75" (22.2 cm) H x 19.5" (49.5 cm) D. Handles extend 1.5" (3.8 cm) forward ;
Weight 65 lbs. (29.5 kg) Net; 83 lbs. (37.7 kg) Shipping.
----SOLD----
Power Amplifier (Tube)
MANLEY
REFERENCE 160
MONOBLOCKS
MADE IN USA
Manley Reference Compact 160 Monoblock:
---SOLD---
REFERENCE 160
MONOBLOCKS
MADE IN USA
Manley Reference Compact 160 Monoblock:
- Vacuum tubes:
- Driver 12BH7A or 6350
- Input l x 12AT7WA
- Input sensitivity: 0.750V
- Input Impedance: 100 Kohm
- ALL-TUBE monoblock design
- Output load impedance: Factory set for 5 ohms nominal
- Max output power: 160 watts on a good day
- S/N ratio: better than -90 dB
- Power consumption: yes, definitely
- RCA Unbalanced input (sometimes had paralleled XLR connector)
- Large filter / reservoir capacitors
- Top deck bias measurement and adjust
- Mercury Magnetics power & output transformers
- Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
- Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.
- Mains Voltage Frequency: 50 ~ 60Hz
- Dimensions: slightly bigger than a bread box
- Shipping weight: around 40 lbs
---SOLD---
Power Amplifier
YAMAHA MX-1
MADE IN JAPAN
Output Power per Channel (20 Hz ~ 20kHz) 0.008% THD 8 ohms = 200W 0.03% THD, 4 ohms = 260W 0.09% THD, 2 ohms = 320W
Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/4/2 ohms = 280/460/630W
DIN Standard Output Power per Channel 1kHz, 0.5% THD, 4 ohms = 300W (H,W)
Dynamic Headroom 8/4/2 ohms = 1.46/2.48/2.94dB
IEC Power (1kHz, 0.01% THD)8 ohms = 225W (H,W)
Power Bandwidth 0.03% THD, 100W, 8 ohms = 10Hz ~ 60kHz
Damping Factor 8 ohms, 1kHz= 250
Input Sensitivity/ Impedance INPUT = 1.46V/20k ohms
Frequency Response (20Hz ~ 20kHz)INPUT = 0+/-0.5dB
Signal to Noise Ratio (IHF-A Network)INPUT (Shorted) = 125dB
Residual Noise (IHF-A Network) = 20uV
Channel Separation (Vol. -30dB)
INPUT (5.1k ohms terminated) = 80dB/60dB
Power Supply AC120V, 60Hz
Power Consumption 560VA/420W
Dimensions (W x H x D) = 438 x 116 x 486mm (17-1/4" x 4-9/16" x 19-1/8") Weight 24.0kg (52 lbs 14 oz)
-----SOLD-----
MADE IN JAPAN
Output Power per Channel (20 Hz ~ 20kHz) 0.008% THD 8 ohms = 200W 0.03% THD, 4 ohms = 260W 0.09% THD, 2 ohms = 320W
Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/4/2 ohms = 280/460/630W
DIN Standard Output Power per Channel 1kHz, 0.5% THD, 4 ohms = 300W (H,W)
Dynamic Headroom 8/4/2 ohms = 1.46/2.48/2.94dB
IEC Power (1kHz, 0.01% THD)8 ohms = 225W (H,W)
Power Bandwidth 0.03% THD, 100W, 8 ohms = 10Hz ~ 60kHz
Damping Factor 8 ohms, 1kHz= 250
Input Sensitivity/ Impedance INPUT = 1.46V/20k ohms
Frequency Response (20Hz ~ 20kHz)INPUT = 0+/-0.5dB
Signal to Noise Ratio (IHF-A Network)INPUT (Shorted) = 125dB
Residual Noise (IHF-A Network) = 20uV
Channel Separation (Vol. -30dB)
INPUT (5.1k ohms terminated) = 80dB/60dB
Power Supply AC120V, 60Hz
Power Consumption 560VA/420W
Dimensions (W x H x D) = 438 x 116 x 486mm (17-1/4" x 4-9/16" x 19-1/8") Weight 24.0kg (52 lbs 14 oz)
-----SOLD-----
Power Amplifier (Tube)
QUAD II FORTY MONOBLOCK
MADE IN UK
Specifications :
Power Output 40W RMS
THD @ 700Hz 0.3% @ 40W 0.03% at 1W
Residual Hum and Noise Better than -80dB
Frequency Response 10Hz - 30kHz (+0dB, -0.5dB)
Damping Factor 20 @ 700Hz (referred to 8 Ohms)
Power Consumption 180VA maximum
Loudspeaker Taps 4 and 8 Ohms
Valves 2 x 6SH7 Input
2 x KT88 Output
1 x 5U4G Rectifier
Input Sensitivity 1V RMS
----SOLD---
MADE IN UK
Specifications :
Power Output 40W RMS
THD @ 700Hz 0.3% @ 40W 0.03% at 1W
Residual Hum and Noise Better than -80dB
Frequency Response 10Hz - 30kHz (+0dB, -0.5dB)
Damping Factor 20 @ 700Hz (referred to 8 Ohms)
Power Consumption 180VA maximum
Loudspeaker Taps 4 and 8 Ohms
Valves 2 x 6SH7 Input
2 x KT88 Output
1 x 5U4G Rectifier
Input Sensitivity 1V RMS
----SOLD---
Power Amplifier (Tube)
CARY CAD100 MONOBLOCK
MADE IN USA
Specifications :
Type............................Push-Pull Amplification in Class A / AB1
Power output...............19.4V rms across 4ohm = 94.09 Watts
...............16.9V rms across 4ohm = 71.04 Watts
...............21V rms across 4ohm = 110.25 Watts
Input sensitivity............1.5V for full output
Input impedance.........100,000 ohm
Noise and Hum...................................90 dB below rated output
Frequency response............................20Hz to 20kHz +/-0.75dB
.............................15Hz to 20kHz +/-2dB
Headroom...........................................12dB
Damping factor....................................Greater than 30
Tubes.................................................1 x ECC83/12AX7 pre-driver, 1 x 12BH7 phase-inverter
..................................................2 x KT-88 (or 2 x 6550) push-pull circuit
Transformers.......................................Toroidal 150% duty cycle power transformer
........................................Dual Toroidal output transformers stacked
Resistors............................................1% metal film
Capacitors..........................................Polystyrene and Polypropylene
PCB...................................................Glass double sided plated through hole
AC power cord.....................................3 conductor shielded
AC power requirements........................100 to 125VAC, 50/60 Hz
Warm-up time......................................3 minutes
Break-in period.....................................50 hours of playing time
Dimensions(w x d x h)..........................43.5 x 32.5 x 15.5cm
Weight................................................35 lbs
Finish.................................................Front panel is anodized black aluminum
................................................with gold lettering. Chassis is painted black aluminum
................................................along with matching aluminum cover.
-----SOLD----
MADE IN USA
Specifications :
Type............................Push-Pull Amplification in Class A / AB1
Power output...............19.4V rms across 4ohm = 94.09 Watts
...............16.9V rms across 4ohm = 71.04 Watts
...............21V rms across 4ohm = 110.25 Watts
Input sensitivity............1.5V for full output
Input impedance.........100,000 ohm
Noise and Hum...................................90 dB below rated output
Frequency response............................20Hz to 20kHz +/-0.75dB
.............................15Hz to 20kHz +/-2dB
Headroom...........................................12dB
Damping factor....................................Greater than 30
Tubes.................................................1 x ECC83/12AX7 pre-driver, 1 x 12BH7 phase-inverter
..................................................2 x KT-88 (or 2 x 6550) push-pull circuit
Transformers.......................................Toroidal 150% duty cycle power transformer
........................................Dual Toroidal output transformers stacked
Resistors............................................1% metal film
Capacitors..........................................Polystyrene and Polypropylene
PCB...................................................Glass double sided plated through hole
AC power cord.....................................3 conductor shielded
AC power requirements........................100 to 125VAC, 50/60 Hz
Warm-up time......................................3 minutes
Break-in period.....................................50 hours of playing time
Dimensions(w x d x h)..........................43.5 x 32.5 x 15.5cm
Weight................................................35 lbs
Finish.................................................Front panel is anodized black aluminum
................................................with gold lettering. Chassis is painted black aluminum
................................................along with matching aluminum cover.
-----SOLD----
Power Amplifier (Tube)
CARY ROCKET 88 R
MADE IN USA
A Stereo Power Amplifier from Cary Audio which produce 60 watts per channel in Class A/B Ultra-linear mode, 30 Watts per channel in Class A Triode mode. Rocket 88R comes with KT-88 output tubes, however it will also work with 6550, KT-66, KT-77, KT-90 or 6L6 output tubes. The choice of output tubes can give the listener the flexibility to adjust the sound up to their individual taste and liking.
It comes standard with Balanced & RCA inputs, 4 or 8 ohm speaker impedance switches for the output terminals, and a useful triode or ultra-linear mode switch. The finishing is black steel chassis with black anodized aluminum front panel comes as a standard. It also features ZERO feedback design as the ultimate sound.
----SOLD----
MADE IN USA
A Stereo Power Amplifier from Cary Audio which produce 60 watts per channel in Class A/B Ultra-linear mode, 30 Watts per channel in Class A Triode mode. Rocket 88R comes with KT-88 output tubes, however it will also work with 6550, KT-66, KT-77, KT-90 or 6L6 output tubes. The choice of output tubes can give the listener the flexibility to adjust the sound up to their individual taste and liking.
It comes standard with Balanced & RCA inputs, 4 or 8 ohm speaker impedance switches for the output terminals, and a useful triode or ultra-linear mode switch. The finishing is black steel chassis with black anodized aluminum front panel comes as a standard. It also features ZERO feedback design as the ultimate sound.
----SOLD----
Power Amplifier
GOLDMUND MIMESIS 28M
MADE IN SWITZERLAND
Specifications :
200W/channel Stereo Power Amplifier> 400W/channel on 8 Ohms before clipping> High-Power JOB 4 circuitry. 2.5 MHz bandwith circuitry. Thermal Grounding full implementation. 2 separate power transformers. Balanced and unbalanced inputs. Fuyll DC and HF speakers and amplifier protection. Size: 44cm W x 44 cm D x 17 cm H. Weight 40 kg
-----SOLD----
MADE IN SWITZERLAND
Specifications :
200W/channel Stereo Power Amplifier> 400W/channel on 8 Ohms before clipping> High-Power JOB 4 circuitry. 2.5 MHz bandwith circuitry. Thermal Grounding full implementation. 2 separate power transformers. Balanced and unbalanced inputs. Fuyll DC and HF speakers and amplifier protection. Size: 44cm W x 44 cm D x 17 cm H. Weight 40 kg
-----SOLD----
Power Amplifier
ISEM
AP-70 D QUASAR
MADE IN FRANCE
High-End power amplifier Dual-Mono 70 Wpc Class A
Weight : 50 kg
----SOLD---
AP-70 D QUASAR
MADE IN FRANCE
High-End power amplifier Dual-Mono 70 Wpc Class A
Weight : 50 kg
----SOLD---
Power Amplifier
CAIRN K1 FACE NORD
MONOBLOCKS
MADE IN FRANCE
The Cairn K1 Face Nord is the high power version of the K1 A. Putting out 200 watts per channel and designed for loads as low as 2 ohms. It features 2 toriodal transformer per monoblock, takes both RCA and XLR inputs and has 2 pairs of speaker terminals
----SOLD----
MONOBLOCKS
MADE IN FRANCE
The Cairn K1 Face Nord is the high power version of the K1 A. Putting out 200 watts per channel and designed for loads as low as 2 ohms. It features 2 toriodal transformer per monoblock, takes both RCA and XLR inputs and has 2 pairs of speaker terminals
----SOLD----
Power Amplifier
AUDIO ANALOGUE
CORELLI
MADE IN ITALY
Corelli provides a power output of over 60 Watts per channel into 8 Ohms, and is easily capable of driving 4 Ohm nominal loads thanks to its generous power supply fed by two 200VA toroidal transformers and its robust power output stage. Corelli is constructed using top quality components; low-noise, high-precision resistors, high-speed polypropylene capacitors of low intrinsic hysteresis and high-linearity wide bandwidth transistors. Its robust chassis and 10mm-thick brushed aluminium front panel are a perfect match for the other products of the Audio Analogue `Composers` range, and its styling of understated elegance will look attractive in any room.
----SOLD---
CORELLI
MADE IN ITALY
Corelli provides a power output of over 60 Watts per channel into 8 Ohms, and is easily capable of driving 4 Ohm nominal loads thanks to its generous power supply fed by two 200VA toroidal transformers and its robust power output stage. Corelli is constructed using top quality components; low-noise, high-precision resistors, high-speed polypropylene capacitors of low intrinsic hysteresis and high-linearity wide bandwidth transistors. Its robust chassis and 10mm-thick brushed aluminium front panel are a perfect match for the other products of the Audio Analogue `Composers` range, and its styling of understated elegance will look attractive in any room.
----SOLD---
Power Amplifier
COUNTERPOINT SA-220
MADE IN USA
Specifications :
Power output : 220W in 8 ohm. 420W in 4 ohm
Tubes used : 4 X 6922
Very powerful and sweet tube-like sound.
-----SOLD---
MADE IN USA
Specifications :
Power output : 220W in 8 ohm. 420W in 4 ohm
Tubes used : 4 X 6922
Very powerful and sweet tube-like sound.
-----SOLD---
Power Amplifier
AUDIO RESEARCH 150.2
MADE IN USA
Audio Research 150.2 combines the groundbreaking Class T digital switching technology first used in the 150M multichannel amplifier with a fixed (non-modular) two-channel design in a package sized like the older 100.2 amplifier. The 150.2 produces a strong 150 WPC into 8 ohms, and 300 WPC into 4 ohms. BAL and SE inputs are provided, along with a 12V trigger and detachable A.C. power cord. Like the 150M, the 150.2 produces very little heat because of its high efficiency, so it is ideal for in-cabinet installations.
---SOLD---
MADE IN USA
Audio Research 150.2 combines the groundbreaking Class T digital switching technology first used in the 150M multichannel amplifier with a fixed (non-modular) two-channel design in a package sized like the older 100.2 amplifier. The 150.2 produces a strong 150 WPC into 8 ohms, and 300 WPC into 4 ohms. BAL and SE inputs are provided, along with a 12V trigger and detachable A.C. power cord. Like the 150M, the 150.2 produces very little heat because of its high efficiency, so it is ideal for in-cabinet installations.
---SOLD---
Power Amplifier (Tube)
SONIC FRONTIERS POWER 1
MADE IN CANADA
Specifications
Power output: 55 watts continuous
Frequency response: 5Hz to 30kHz
Input sensitivity: 0.94V RMS (balanced/single ended)
Input impedance: 200K ohms (balanced), 100K ohms (single ended)
Damping factor: >35
Output impedance: 0.28 ohms
Tubes : Two matched pairs of 6550C/KT88 power output tubes and six 6922 input/driver tubes
Dimensions: 380 x 510 x 230mm
Weight: 22kg
----SOLD---
MADE IN CANADA
Specifications
Power output: 55 watts continuous
Frequency response: 5Hz to 30kHz
Input sensitivity: 0.94V RMS (balanced/single ended)
Input impedance: 200K ohms (balanced), 100K ohms (single ended)
Damping factor: >35
Output impedance: 0.28 ohms
Tubes : Two matched pairs of 6550C/KT88 power output tubes and six 6922 input/driver tubes
Dimensions: 380 x 510 x 230mm
Weight: 22kg
----SOLD---
Power Amplifier
SPECTRON MUSICIAN III SIGNATURE
MADE IN USA
Features :
Digital pulse width modulation switching amplifier.
Feedback loop 10 times faster than typical conventional amplifiers.
High head room, 100V peak and 50A peak.
No crossover distortion.
Drives the most difficult speakers, stable to .1 ohm.
Foldback current limit. Automatic overload recovery.
Profesional quality balanced line input.
Phase invert. Rear panel selectable.
RCA and XLR input. Rear panel selectable.
In-rush resistor bypass. More and tighter bass.
Isolated low level power supplies. Eliminates noise from AC line in low level circuits.
Speaker protection. Turns amp off for excessive DC or high frequency.
Stable into .1 ohm.
High efficiency for minimal power consumption.
Small size.
Specifications :
600 Watts into 8 Ohm
800W into 4 Ohm
1400W into 2 Ohm
Peak Power: 5000Watts over 330 msec ( Peak current: 50A)
THD 22 kHz)
Noise: 92% (Amp module)
Line volage: 100, 120 or 240 VAC 50/60Hz Switch selectable
Power draw, no signal: 40W
Weight: 18kg (38 lbs) Shipping: 55 lbs
Size: 431mm wide, 133mm high, 368mm deep (17”H, 5 ¼”H, 14”D)
---SOLD---
MADE IN USA
Features :
Digital pulse width modulation switching amplifier.
Feedback loop 10 times faster than typical conventional amplifiers.
High head room, 100V peak and 50A peak.
No crossover distortion.
Drives the most difficult speakers, stable to .1 ohm.
Foldback current limit. Automatic overload recovery.
Profesional quality balanced line input.
Phase invert. Rear panel selectable.
RCA and XLR input. Rear panel selectable.
In-rush resistor bypass. More and tighter bass.
Isolated low level power supplies. Eliminates noise from AC line in low level circuits.
Speaker protection. Turns amp off for excessive DC or high frequency.
Stable into .1 ohm.
High efficiency for minimal power consumption.
Small size.
Specifications :
600 Watts into 8 Ohm
800W into 4 Ohm
1400W into 2 Ohm
Peak Power: 5000Watts over 330 msec ( Peak current: 50A)
THD 22 kHz)
Noise: 92% (Amp module)
Line volage: 100, 120 or 240 VAC 50/60Hz Switch selectable
Power draw, no signal: 40W
Weight: 18kg (38 lbs) Shipping: 55 lbs
Size: 431mm wide, 133mm high, 368mm deep (17”H, 5 ¼”H, 14”D)
---SOLD---
Power Amplifier (Tube)
QUICKSILVER MONO 100
MADE IN USA
SPECIFICATIONS :
Power Output 100 watts into 4 or 8 ohms
Power Bandwidth 18 Hz to 80 KHz
Damping Factor 19
Input Sensitivity 1.5 volts
Input Impedance 100 K ohms
Power Consumption 115 watts at idle 300 watts at full power
Tube Complement 1 - 12AX7 input
1 - 12BH7 driver
2 - KT88 outputs
Dimensions 5 1/2' high x 14 1/2“ deep x 9 1/8” wide
Finish Chrome chassis Black transformers and capacitors
Weight 31 lbs
----SOLD---
MADE IN USA
SPECIFICATIONS :
Power Output 100 watts into 4 or 8 ohms
Power Bandwidth 18 Hz to 80 KHz
Damping Factor 19
Input Sensitivity 1.5 volts
Input Impedance 100 K ohms
Power Consumption 115 watts at idle 300 watts at full power
Tube Complement 1 - 12AX7 input
1 - 12BH7 driver
2 - KT88 outputs
Dimensions 5 1/2' high x 14 1/2“ deep x 9 1/8” wide
Finish Chrome chassis Black transformers and capacitors
Weight 31 lbs
----SOLD---
Power Amplifier
KRELL KSA-300S
MADE IN USA
Description:
Solid-state stereo power amplifier. Power rating: 300Wpc into 8 ohms, doubles with each halving of load impedance down to 1 ohm (24.8dBW). Frequency response: 20Hz–20kHz, +0.0dB, –0.1dB; 1Hz–150kHz, +0.0dB, –3dB. Distortion: <0.1% at 1kHz, <0.3% at 20kHz, full power. Slew rate: 100V/µs. Input sensitivity: 2.5V rms. Gain: 25.5dB. Damping factor: >120. S/N ratio: 110dB. Input impedance: 47k ohms. Power consumption, idle: 130W.
Dimensions: 19" W by 8.5" H by 24" D. Weight: 84 kg (net)
----SOLD----
MADE IN USA
Description:
Solid-state stereo power amplifier. Power rating: 300Wpc into 8 ohms, doubles with each halving of load impedance down to 1 ohm (24.8dBW). Frequency response: 20Hz–20kHz, +0.0dB, –0.1dB; 1Hz–150kHz, +0.0dB, –3dB. Distortion: <0.1% at 1kHz, <0.3% at 20kHz, full power. Slew rate: 100V/µs. Input sensitivity: 2.5V rms. Gain: 25.5dB. Damping factor: >120. S/N ratio: 110dB. Input impedance: 47k ohms. Power consumption, idle: 130W.
Dimensions: 19" W by 8.5" H by 24" D. Weight: 84 kg (net)
----SOLD----
Power Amplifier (Tube)
ROGUE AUDIO STEREO 90
MADE IN USA
General Features:
- Ultra-wide bandwidth output transformers
- Massive fully regulated high voltage supply
- Matched quad output tubes
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- User selectable 4 and 8 ohm output taps
- User selectable triode or ultralinear output
- (4) KT88/6550, (2) 6SN7, (2) 12AX7 tube complement
- Built in bias meter
- Integral tube cage
- Machined aluminum faceplate
- Mechanically isolated transformers
- Heavy (2 ounce) copper circuit board
- All precision components
- Fully tested, burned in, and auditioned
Specifications:
- output power: 90 WPC minimum
- input impedance: 200K Ohms
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1.0% at rated power
- input sensitivity: 1.0V RMS
- dimensions: 18"W x 15¾"D x 7"H
- weight: 60 lbs.
- power requirements: 115/230V - 50 - 60Hz
---SOLD---
MADE IN USA
General Features:
- Ultra-wide bandwidth output transformers
- Massive fully regulated high voltage supply
- Matched quad output tubes
- Heavy-duty gold plated RCA inputs
- Heavy-duty gold plated binding posts
- User selectable 4 and 8 ohm output taps
- User selectable triode or ultralinear output
- (4) KT88/6550, (2) 6SN7, (2) 12AX7 tube complement
- Built in bias meter
- Integral tube cage
- Machined aluminum faceplate
- Mechanically isolated transformers
- Heavy (2 ounce) copper circuit board
- All precision components
- Fully tested, burned in, and auditioned
Specifications:
- output power: 90 WPC minimum
- input impedance: 200K Ohms
- frequency response: 5Hz - 50KHz ± 1dB
- THD: <0.1% typ., <1.0% at rated power
- input sensitivity: 1.0V RMS
- dimensions: 18"W x 15¾"D x 7"H
- weight: 60 lbs.
- power requirements: 115/230V - 50 - 60Hz
---SOLD---
Power Amplifier
MARK LEVINSON NO.332
MADE IN USA
Highlights:
Dual mono design, fully balanced circuitry
Sliding bias Class A operation
Rated 200 W x 2 into 8 ohm, 400 W into 4 ohm, 800 W into 2 ohm
Balanced XLR + single-ended RCA inputs, dual binding posts to facilitate biwiring.
-----SOLD----
MADE IN USA
Highlights:
Dual mono design, fully balanced circuitry
Sliding bias Class A operation
Rated 200 W x 2 into 8 ohm, 400 W into 4 ohm, 800 W into 2 ohm
Balanced XLR + single-ended RCA inputs, dual binding posts to facilitate biwiring.
-----SOLD----
Power Amplifier
ELECTROCOMPANIET
AMPLIWIRE 75
MADE IN NORWAY
The Electrocompaniet AW 75 power amplifier is known for its uncoloured and excellent reproduction qualities. From the first note of any familiar recording, you will be captivated by the AW 75 and by the musical enjoyment it will give you. Audiophiles, recording engineers, record producers and reviewers around the world reply on the AW75's faithful reproduction of the
original master recording.
---SOLD---
AMPLIWIRE 75
MADE IN NORWAY
The Electrocompaniet AW 75 power amplifier is known for its uncoloured and excellent reproduction qualities. From the first note of any familiar recording, you will be captivated by the AW 75 and by the musical enjoyment it will give you. Audiophiles, recording engineers, record producers and reviewers around the world reply on the AW75's faithful reproduction of the
original master recording.
---SOLD---
Power Amplifier
PS AUDIO HCA2
MADE IN USA
The HCA-2 features:
150 watt per channel hybrid class D power amplifier. One of the first class D amplifiers to be built by any high-end audio company, the HCA-2 was a hybrid incorporating a class A analog input stage with a class D output stage. Winner of Stereophile magazine's product of the year, this revolutionary power amplifier is a classic design that is still enjoyed by thousands of Audiophiles and music lovers the world over.
---SOLD---
MADE IN USA
The HCA-2 features:
150 watt per channel hybrid class D power amplifier. One of the first class D amplifiers to be built by any high-end audio company, the HCA-2 was a hybrid incorporating a class A analog input stage with a class D output stage. Winner of Stereophile magazine's product of the year, this revolutionary power amplifier is a classic design that is still enjoyed by thousands of Audiophiles and music lovers the world over.
- A built in High Current Ultimate Outlet
- Single ended RCA and true balanced XLR connectors
- Outputs are WBT 5-way binding posts
- Over 70 dB of common mode rejection
- Huge toroidal transformer
- PS communication bus
- DC trigger for AV use
- Clean, no heat design
---SOLD---
Power Amplifier (Tube)
MANLEY 50 MONOBLOCKS
MADE IN USA
Vacuum Tubes: 4 x EL84 Output,
l x 12AT7WA Input,
1 x 6414 Driver
Output Power: 53 Watts
Freq. Response +.5 dB: 10 Hz - 90 KHz
Input Sensitivity: 460 mV nominal
Input Impedance: 100 Kohm
Load Impedance: 5 ohm
S/N Ratio @50W: -80 dB
Dynamic Range: 86dB
Power Consumption: 100 Watts (idle)
168 Watts (Full Power)
Factory set for 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency: 50~ 60Hz
Dimensions: W=12", D=10", H=5"
Shipping Weight: 17 Ibs. each
---SOLD---
MADE IN USA
Vacuum Tubes: 4 x EL84 Output,
l x 12AT7WA Input,
1 x 6414 Driver
Output Power: 53 Watts
Freq. Response +.5 dB: 10 Hz - 90 KHz
Input Sensitivity: 460 mV nominal
Input Impedance: 100 Kohm
Load Impedance: 5 ohm
S/N Ratio @50W: -80 dB
Dynamic Range: 86dB
Power Consumption: 100 Watts (idle)
168 Watts (Full Power)
Factory set for 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency: 50~ 60Hz
Dimensions: W=12", D=10", H=5"
Shipping Weight: 17 Ibs. each
---SOLD---
Power Amplifier
KRELL FPB 200
MADE IN USA
SPECIFICATIONS:
FREQUENCYRESPONSE 20 Hz to 20 kHz, +0 dB, -0.05 dB; 0.1 Hz to 240 kHz, +0 dB, -3 dB
SIGNALTO NOISE RATIO 114 dB GAIN 26.4 dB THD 1 kHz <0.03% , 20 kHz <0.16%
INPUT IMPEDANCE 100 kOhms
INPUT SENSITIVITY 2.53 Vrms
OUTPUT POWER 8 Ohms 200 W x 2, 4 Ohms 400W x 2, 2 Ohms 800W x 2.
OUTPUT VOLTAGE Peak to Peak138 V; RMS 49V
POWER CONSUMPTION Stand-by 30 W , Idle 150W , Max 1500W
INPUTS 1 set of Balanced XLR, 1 set of RCA
OUTPUTS SPEAKER BINDING POSTS 2 pairs upper and lower
WEIGHT 42kg
---SOLD---
MADE IN USA
SPECIFICATIONS:
FREQUENCYRESPONSE 20 Hz to 20 kHz, +0 dB, -0.05 dB; 0.1 Hz to 240 kHz, +0 dB, -3 dB
SIGNALTO NOISE RATIO 114 dB GAIN 26.4 dB THD 1 kHz <0.03% , 20 kHz <0.16%
INPUT IMPEDANCE 100 kOhms
INPUT SENSITIVITY 2.53 Vrms
OUTPUT POWER 8 Ohms 200 W x 2, 4 Ohms 400W x 2, 2 Ohms 800W x 2.
OUTPUT VOLTAGE Peak to Peak138 V; RMS 49V
POWER CONSUMPTION Stand-by 30 W , Idle 150W , Max 1500W
INPUTS 1 set of Balanced XLR, 1 set of RCA
OUTPUTS SPEAKER BINDING POSTS 2 pairs upper and lower
WEIGHT 42kg
---SOLD---
