Pre Amplifier

TRIGON DIALOG
MADE IN GERMANY
------SOLD-----
MADE IN GERMANY
------SOLD-----
Pre Amplifier

GRYPHON LINESTAGE
MADE IN DENMARK
-----SOLD------
MADE IN DENMARK
-----SOLD------
Pre Amplifier

KRELL KAV-280P
MADE IN USA
FEATURES
The KAV-280p uses current tunnel and surface mount technology derived directly from the state-of-the-art Krell Current Tunnel (KCT) preamplifier. Its extremely wide bandwidth makes the KAV-280p the ideal preamplifier for today's high resolution sources. The extended frequency response made possible by Krell Current Mode circuitry insures fidelity and phase coherence within the audio passband for convincing recovery of the most complex audio programs.
The single ended and balanced inputs are buffered for optimum interface characteristics. All circuitry is direct-coupled; there are no capacitors in the signal path. Four layer copper clad circuit cards utilize a proprietary ground scheme and are designed by Krell engineers to minimize noise and crosstalk. High-speed, bipolar transistors are used throughout.
The power supply is heavily regulated and utilizes a 100VA torroidal transformer. As in the KCT, regulation is nested throughout the circuit to insure timely voltage delivery to the various gain stages. A micro controller with highly reliable, sealed relays and gold contacts manages input selection duties.
Condition : Pre-Owned, Mint
Price : Rp 20.000.000,-
MADE IN USA
FEATURES
The KAV-280p uses current tunnel and surface mount technology derived directly from the state-of-the-art Krell Current Tunnel (KCT) preamplifier. Its extremely wide bandwidth makes the KAV-280p the ideal preamplifier for today's high resolution sources. The extended frequency response made possible by Krell Current Mode circuitry insures fidelity and phase coherence within the audio passband for convincing recovery of the most complex audio programs.
The single ended and balanced inputs are buffered for optimum interface characteristics. All circuitry is direct-coupled; there are no capacitors in the signal path. Four layer copper clad circuit cards utilize a proprietary ground scheme and are designed by Krell engineers to minimize noise and crosstalk. High-speed, bipolar transistors are used throughout.
The power supply is heavily regulated and utilizes a 100VA torroidal transformer. As in the KCT, regulation is nested throughout the circuit to insure timely voltage delivery to the various gain stages. A micro controller with highly reliable, sealed relays and gold contacts manages input selection duties.
Condition : Pre-Owned, Mint
Price : Rp 20.000.000,-
Pre Amplifier (Tube)

MANLEY SHRIMP
MADE IN USA
.......SOLD......
MADE IN USA
- Very short, simple minimalist signal path. All-tube design. 2 x 12AT7 + 2 x 7044
- Generous energy storage via large power supply capacitors for more impact in the bass.
- No global feedback makes the Shrimp very fast sounding.
- Non-inverting two-tube gain stage is direct-coupled for most pure signal path.
- Cool White-follower output stage provides low 50 Ohm output impedance. This is much better than a boring plain ol' cathode follower. The Shrimp can drive anything, not to worry.
- Filament supply floated 80V above chassis ground for quieter operation and longer tube life.
- NOBLE audiophile-grade level and balance pots. We use the nice parts in here!
- MIT/MultiCap polypropylene audiophile-grade signal coupling capacitors, including two 30 uF monsters on the output stages.
- Warm-up delay / MUTE button. Features and quality components usually not found on entry-level pieces.
.......SOLD......
Pre Amplifier

PRIMARE PRE 32
MADE IN SWEDEN
Specifications
Conditions : Pre-Owned, Mint
Price : Rp 26.000.000,-
MADE IN SWEDEN
Specifications
- Analogue Inputs 2 pair XLR (L & R) 4 pair RCA (L & R)
- Other In/outputs RS232, IR in/out, Trigger in/out, RF.
- Optional MM30 Media i/o module
- Optional high quality aptX Bluetooth upgrade
- Input Impedance 15k Both RCA and XLR
- Analogue Record Output 1 pair RCA (L & R)
- Pre Output 2 pair RCA (L & R), 1 pair XLR (L & R)
- Output Impedance 110 ohms
- Frequency Response 20Hz – 100kHz -3dB
- THD + N < 0.003%, 20Hz – 100kHz, 0dB gain.
- Signal to Noise -115 dBV
- Max in /out level 10Vrms
- Gain 16dB
- Power Consumption Standby: 0.2W; Operate: 23W
- Dimensions (wxdxh) 430 x 385 x 105mm
- Weight 10.5 kg
Conditions : Pre-Owned, Mint
Price : Rp 26.000.000,-
Pre Amplifier

THRESHOLD STASIS- R 3.0
MADE IN USA
Features
-----SOLD-----
MADE IN USA
Features
- Fully balanced from input to output providing extremely high common-mode rejection and cancellation of most distortion artifacts
- All-discrete direct-coupled solid state gainblocks
- Fully complementary circuitry
- Short direct signal paths
- Rotary volume control, 80 dB range in 0.5 dB increments
- Easy-to-read LCD matrix display (blue/white, 2-line, 16 character)
- Custom machined aluminum infrared remote control
- Oversize toroidal power transformer
- Separate power supply sections for left and right channels
- Separate independent power supply for digital control circuitry
- Premium components such as military-grade precision resistors, computer-grade capacitors, military-grade glass-epoxy circuit boards
- Gold-plated RCA jacks ensure optimum signal transfer and extended life
- Neutrik XLR connectors
- Trigger output (12V) for on/off control of ancillary equipment (e.g. power amplifier, active subwoofer, etc.)
- Bypass mode for integration into Home Theater system
- RS-232C port for software updates and future features
- Threshold Data Link (T-LINK) port for control and communication with other Threshold equipment
- Traditional Threshold rugged chassis construction
- High reliability
- Unsurpassed precision and sonic excellence
- Inputs: 1 balanced (XLR) and 5 unbalanced (RCA) stereo pairs
- Line outputs: balanced (XLR) and unbalanced (RCA) stereo pairs
- Record outputs: unbalanced (RCA) stereo pair
- Rack-mountable design (optional rack-mount accessories required)
- Attractive polished silver-anodized aluminum front panel
- Handcrafted in the USA
- Frequency Response: DC-100kHz; +/- 0.5dB 20Hz-20kHz
- Distortion: 0.02% at 1kHz, 2Vrms Output
- Gain: 12 dB
- Signal-to-Noise Ratio: Greater than 100dB (Ref. 1V input, maximum gain, 20kHz bandwidth)
- Input Impedance: 20k Ohm balanced, 10k Ohm unbalanced
- Input Sensitivity: 1.12V RMS
- Output Impedance: less than 100 Ohms
- Output level: maximum 16Vrms balanced, 8Vrms unbalanced
- Trigger output: 12V for on/off control of ancilary equipment
- 17.1'' W x 13.5'' D x 3.5'' H (3.75'' H including rubber feet)
- 43.5 cm W x 34.3 cm D x 8.9 cm H (9.6 cm H including rubber feet)
- Shipping weight: 16 lbs., 8 kg
- Net weight: 12 lbs., 6 kg
-----SOLD-----
Pre Amplifier

ADCOM GFP 750
MADE IN USA
----SOLD-----
MADE IN USA
----SOLD-----
Pre Amplifier

ORPHEUS TWO
MADE IN SWITZERLAND
The Orpheus engineering team has created a unique high-end two-channel preamplifier that offers multi-channel flexibility at no sacrifice in absolute performance. The future-proof Orpheus Two can be re-configured to suit your changing needs quickly and easily.
Ingenious software programming permits the user to quickly re-assign one or two sets of three stereo inputs to operate as a six-channel input. Similarly, multiple stereo outputs can be re-configured as a single six-channel output.
Stereo: 1 balanced stereo input, 6 phono stereo inputs, 1 balanced stereo output, 2 phono stereo outputs
Stereo + Multi-Amp : 1 balanced stereo input, 6 phono stereo inputs, 1 balanced stereo output, 2 phono stereo outputs, 2 additional phono stereo outputs with independent level control (for multi-room applications, etc.)
Single Multi-Channel : 1 six-channel input, 1 balanced stereo input, 3 phono stereo inputs, 1 six-channel output (activated automatically when the six-channel input is selected), 1 balanced and 2 phono stereo outputs (activated automatically when a stereo input is selected)
Dual Multi-Channel : 2 six-channel inputs, 1 balanced stereo input, 1 six-channel output (activated automatically when a six-channel input is selected), 1 balanced and 2 phono stereo outputs (activated automatically when a stereo input is selected)
-----SOLD-----
MADE IN SWITZERLAND
The Orpheus engineering team has created a unique high-end two-channel preamplifier that offers multi-channel flexibility at no sacrifice in absolute performance. The future-proof Orpheus Two can be re-configured to suit your changing needs quickly and easily.
Ingenious software programming permits the user to quickly re-assign one or two sets of three stereo inputs to operate as a six-channel input. Similarly, multiple stereo outputs can be re-configured as a single six-channel output.
Stereo: 1 balanced stereo input, 6 phono stereo inputs, 1 balanced stereo output, 2 phono stereo outputs
Stereo + Multi-Amp : 1 balanced stereo input, 6 phono stereo inputs, 1 balanced stereo output, 2 phono stereo outputs, 2 additional phono stereo outputs with independent level control (for multi-room applications, etc.)
Single Multi-Channel : 1 six-channel input, 1 balanced stereo input, 3 phono stereo inputs, 1 six-channel output (activated automatically when the six-channel input is selected), 1 balanced and 2 phono stereo outputs (activated automatically when a stereo input is selected)
Dual Multi-Channel : 2 six-channel inputs, 1 balanced stereo input, 1 six-channel output (activated automatically when a six-channel input is selected), 1 balanced and 2 phono stereo outputs (activated automatically when a stereo input is selected)
-----SOLD-----
Pre Amplifier (Tube)

VTL TL-2.5
MADE IN USA
Data Specifications :
Vacuum Tube Complement : 2 x 12AU7, 2 x 12AT7
Inputs : 6 Single ended Line inputs
2 RCA Processor / Tape in
Outputs : 2 pairs Single-ended RCA
2 pairs Processor / Tape Out
Remote Control Functions : Volume and Mute
Gain : 20 dB
Output Impedance : 200 Ohms
Input Impedance : 20K Ohms
Frequency response + 0 - 3 dB : 1 Hz - 60KHz
Maximum Output Voltage < 1% THD : 60 Volts
Channel Separation : > 75 dB @ 1KHz
Power Consumption : 100 Watts
Dimensions (W x D H) : 19 x 14 x 3.75 inches
48.25 x 35.5 x 9.5 cm
Weight : 25 lbs (11Kg) Fully packed
-----SOLD------
MADE IN USA
Data Specifications :
Vacuum Tube Complement : 2 x 12AU7, 2 x 12AT7
Inputs : 6 Single ended Line inputs
2 RCA Processor / Tape in
Outputs : 2 pairs Single-ended RCA
2 pairs Processor / Tape Out
Remote Control Functions : Volume and Mute
Gain : 20 dB
Output Impedance : 200 Ohms
Input Impedance : 20K Ohms
Frequency response + 0 - 3 dB : 1 Hz - 60KHz
Maximum Output Voltage < 1% THD : 60 Volts
Channel Separation : > 75 dB @ 1KHz
Power Consumption : 100 Watts
Dimensions (W x D H) : 19 x 14 x 3.75 inches
48.25 x 35.5 x 9.5 cm
Weight : 25 lbs (11Kg) Fully packed
-----SOLD------
Pre Amplifier (Tube)

CROFT VITALE
HANDMADE BY UK
------SOLD------
HANDMADE BY UK
------SOLD------
Pre Amplifier

AUDIO ANALOGUE BELLINI
VIRTUAL BATTERY
MADE IN ITALY
High performance Preamplifier With Virtual Battery Supply
The new Bellini Virtual Battery REV2.0 preamplifier represents a quantum leap for Audio Analogue’s composers line, in sound quality, manufacturing and assembly perfection, look & style and performances, yet retaining the famous family look and ease of use.
The elegant yet sober appearance of the Bellini Virtual Battery REV2.0 will allow for a discrete placement in every domestic environment, with both classic style or modern furniture.
The new, totally remote-controlled discrete components circuit deliver clean, crystal-clear with bandwidth and dynamics that meet the requirements from the new high-resolution digital sources.
The unique off-line virtual battery supply, improved version of the one already introduced with the Aria phono preamplifier, ensures an absolute immunity to every disturbance that could come from the mains through the power transformer’s and regulators’ parasytic capacitances.
The high-performance discrete components preamplifier circuit operates a perfect interface between the integrated bufferless resistor network potentiomenter and the power amp’s input, contributing to the balanced sound of the amplifier. Solid state input selectors allow for indefinite best quality performance (no sound detriment due to metallic contacts ageing and wear-out).
The special line/phono input can be set to operate as a phono MM input, phono MC, or even line. It uses the samerefined, high-dynamics circuit as the Aria phono preamplifier and gives user the maximum flexibility to set the interface to the cartridge and the gain.
The balanced input and the quadruple outputs (two single-ended sets and two balanced sets) allow for a universal interface capability and passive bi-amping. A 12V trigger output allows for slaveing the power amplifier or any other equipment switching to the Bellini Virtual Battery REV2.0: all the system can be turned on and off using the preamplifier’s remote.
A special bypass feature, selectable by remote’s “setup” option, allows the user to turn the Bellini Virtual Battery REV2.0 in a straight line from a specified input to the outputs, to include the preamplifier in a multichannel system in which the related power amplifier is used to drive the front speakers, while using the same speakers for two channel listening using the stereo sources connected to the preamplifier.
The seven-keys solid brass remote control allows for a more flexible control of the Bellini VB. Of course, all the main features of the amplifiers can be used by the front panel’s simple controls.
-----SOLD-----
VIRTUAL BATTERY
MADE IN ITALY
High performance Preamplifier With Virtual Battery Supply
The new Bellini Virtual Battery REV2.0 preamplifier represents a quantum leap for Audio Analogue’s composers line, in sound quality, manufacturing and assembly perfection, look & style and performances, yet retaining the famous family look and ease of use.
The elegant yet sober appearance of the Bellini Virtual Battery REV2.0 will allow for a discrete placement in every domestic environment, with both classic style or modern furniture.
The new, totally remote-controlled discrete components circuit deliver clean, crystal-clear with bandwidth and dynamics that meet the requirements from the new high-resolution digital sources.
The unique off-line virtual battery supply, improved version of the one already introduced with the Aria phono preamplifier, ensures an absolute immunity to every disturbance that could come from the mains through the power transformer’s and regulators’ parasytic capacitances.
The high-performance discrete components preamplifier circuit operates a perfect interface between the integrated bufferless resistor network potentiomenter and the power amp’s input, contributing to the balanced sound of the amplifier. Solid state input selectors allow for indefinite best quality performance (no sound detriment due to metallic contacts ageing and wear-out).
The special line/phono input can be set to operate as a phono MM input, phono MC, or even line. It uses the samerefined, high-dynamics circuit as the Aria phono preamplifier and gives user the maximum flexibility to set the interface to the cartridge and the gain.
The balanced input and the quadruple outputs (two single-ended sets and two balanced sets) allow for a universal interface capability and passive bi-amping. A 12V trigger output allows for slaveing the power amplifier or any other equipment switching to the Bellini Virtual Battery REV2.0: all the system can be turned on and off using the preamplifier’s remote.
A special bypass feature, selectable by remote’s “setup” option, allows the user to turn the Bellini Virtual Battery REV2.0 in a straight line from a specified input to the outputs, to include the preamplifier in a multichannel system in which the related power amplifier is used to drive the front speakers, while using the same speakers for two channel listening using the stereo sources connected to the preamplifier.
The seven-keys solid brass remote control allows for a more flexible control of the Bellini VB. Of course, all the main features of the amplifiers can be used by the front panel’s simple controls.
-----SOLD-----
Pre Amplifier (Tube)

ATMA-SPHERE MP-3 MK 3.1
MADE IN USA
Features:- Balanced Differential Design® - XLR connectors for phono and auxiliary 1 and 2 - XLR output connections - Patented direct-coupled Circlotronic® output - Zero feedback design throughout - Balanced passive phono equalization - Precision 23 position stepped volume control built with 96 resistors on a custom built switch - Two tape monitors inputs (tape functions use RCA's) - Precision components used throughout - Total system phase switch - "Star" grounding used throughout Options: - V-Cap Teflon® coupling caps - Damping Package - Power Supply Regulation - Caddock resistor package - Low Output MC phono step-up transformers for cartridges under 0.25mV output Specifications: - Line section frequency response: 0.2Hz-200KHz, +0 db, -2db - Line section gain: ~15db - Line section input impedance 500K single ended / 1M balanced - phono section input impedance 47K - phono section gain: ~50db - Phono section frequency response: .5Hz-90KHz within 1/2 db - RIAA accuracy: within 0.1 db - RIAA phono sens. for 0.5V @ 1KHz: 0.2mV - Minimum recommended phono input: 0.24mV - Phono section output at clipping: 120V p-p - Phono input overload: 500mv - Power supply storage: 50 Joules - Tube complement: 7) 12AT7 (phono section) 2) 12AU7 (line section) 2) 6SN7GT (output section) - Dimensions: 17" wide (front panel is 19") by ~13" deep including knobs and connectors, by 6" high (front panel) - Weight: 20 pounds
------SOLD------
MADE IN USA
Features:- Balanced Differential Design® - XLR connectors for phono and auxiliary 1 and 2 - XLR output connections - Patented direct-coupled Circlotronic® output - Zero feedback design throughout - Balanced passive phono equalization - Precision 23 position stepped volume control built with 96 resistors on a custom built switch - Two tape monitors inputs (tape functions use RCA's) - Precision components used throughout - Total system phase switch - "Star" grounding used throughout Options: - V-Cap Teflon® coupling caps - Damping Package - Power Supply Regulation - Caddock resistor package - Low Output MC phono step-up transformers for cartridges under 0.25mV output Specifications: - Line section frequency response: 0.2Hz-200KHz, +0 db, -2db - Line section gain: ~15db - Line section input impedance 500K single ended / 1M balanced - phono section input impedance 47K - phono section gain: ~50db - Phono section frequency response: .5Hz-90KHz within 1/2 db - RIAA accuracy: within 0.1 db - RIAA phono sens. for 0.5V @ 1KHz: 0.2mV - Minimum recommended phono input: 0.24mV - Phono section output at clipping: 120V p-p - Phono input overload: 500mv - Power supply storage: 50 Joules - Tube complement: 7) 12AT7 (phono section) 2) 12AU7 (line section) 2) 6SN7GT (output section) - Dimensions: 17" wide (front panel is 19") by ~13" deep including knobs and connectors, by 6" high (front panel) - Weight: 20 pounds
------SOLD------
Pre Amplifier

GRYPHON ELECTRA
MADE IN DENMARK
Dual Mono Pre Amplifier
-----SOLD-------
MADE IN DENMARK
Dual Mono Pre Amplifier
-----SOLD-------
Pre Amplifier (Tube)

SONIC FRONTIERS
SFL 1 SIGNATURE
MADE IN CANADA
Specifications :
Type................................................Hybrid tube pre-amplifier
................................................For Line stage only
Tube................................................Single CV4024 / M8162 tube
Inputs..............................................4
Frequency response.........................2 Hz to 100 kHz +/- 0.5dB
.........................>200 kHz, -0.3 dB (100K load)
THD & noise....................................<0.1% from 20 Hz to 20 khz
.....................................Typically < 0.05% @ 1 kHz
Gain................................................20 dB @ 1 kHz
Noise...............................................180 uV unweighted
Intermodulation distortion..................< 0.3%, @ 2V output
Input inpedance................................45 Kohm(Direct input), 90 Kohm(Normal inputs)
Output impedance............................320 ohms @1 kHz
Output voltage..................................Maximum 25 Vrms
Maximum input................................2.5 Vrms
Stereo seperation.............................60 dB @ 1 kHz (Cosstalk)
Dimensions(w x d x h)......................48.5 x 31.5 x 11.5 cm
Weight............................................9 kg
----SOLD----
SFL 1 SIGNATURE
MADE IN CANADA
Specifications :
Type................................................Hybrid tube pre-amplifier
................................................For Line stage only
Tube................................................Single CV4024 / M8162 tube
Inputs..............................................4
Frequency response.........................2 Hz to 100 kHz +/- 0.5dB
.........................>200 kHz, -0.3 dB (100K load)
THD & noise....................................<0.1% from 20 Hz to 20 khz
.....................................Typically < 0.05% @ 1 kHz
Gain................................................20 dB @ 1 kHz
Noise...............................................180 uV unweighted
Intermodulation distortion..................< 0.3%, @ 2V output
Input inpedance................................45 Kohm(Direct input), 90 Kohm(Normal inputs)
Output impedance............................320 ohms @1 kHz
Output voltage..................................Maximum 25 Vrms
Maximum input................................2.5 Vrms
Stereo seperation.............................60 dB @ 1 kHz (Cosstalk)
Dimensions(w x d x h)......................48.5 x 31.5 x 11.5 cm
Weight............................................9 kg
----SOLD----
Pre Amplifier (Tube)

VAC 20.1
MADE IN USA
------SOLD------
MADE IN USA
------SOLD------
Pre Amplifier

AUDIO RESEARCH LS3
MADE IN USA
------SOLD------
MADE IN USA
------SOLD------
Pre Amplifier

ARCAM FMJ C31
MADE IN UK
The design of the C31 features a simple, accurate and clean signal path. The reed relay input switching dispenses with the compromises of mechanical or conventional relay designs, resulting in switching with immeasurable noise and distortion. The studio grade electronic volume controls deliver precision variation of volume level whilst maintaining the subtle nuances of the music and delivering long-term reliability. Connections are designed to be flexible with conventional unbalanced (for direct connection to power amplifiers and the purest fidelity), buffered unbalanced (for longer cable runs) and balanced output connections for use in electrically noisy environments. Inputs are wide ranging and include five line level inputs, two independent tape loops and an optional single stage MM/MC phono input . Pre-amplifier section Output stage Construction Power supply General Power consumption (max) 30VA Size 430W x 370D x 110H mm inc. feet Weight (net) 9.3kg
-----SOLD-----
MADE IN UK
The design of the C31 features a simple, accurate and clean signal path. The reed relay input switching dispenses with the compromises of mechanical or conventional relay designs, resulting in switching with immeasurable noise and distortion. The studio grade electronic volume controls deliver precision variation of volume level whilst maintaining the subtle nuances of the music and delivering long-term reliability. Connections are designed to be flexible with conventional unbalanced (for direct connection to power amplifiers and the purest fidelity), buffered unbalanced (for longer cable runs) and balanced output connections for use in electrically noisy environments. Inputs are wide ranging and include five line level inputs, two independent tape loops and an optional single stage MM/MC phono input . Pre-amplifier section Output stage Construction Power supply General Power consumption (max) 30VA Size 430W x 370D x 110H mm inc. feet Weight (net) 9.3kg
-----SOLD-----
Pre Amplifier

MOON P5 LIMITED EDITION
MADE IN CANADA
P-5 _Limited Edition SimAudio Moon preamplifier: Balanced differential dual-mono preamplifier using a class "A" open loop circuit topology. This is a 2 chassis system that Sim only made 250 pcs.The separate power supply chassis actually houses separate power supplies for the digital vs analog components, resulting in the superb clarity of detail, dynamics, and soundstaging this component is known for.
------SOLD------
MADE IN CANADA
P-5 _Limited Edition SimAudio Moon preamplifier: Balanced differential dual-mono preamplifier using a class "A" open loop circuit topology. This is a 2 chassis system that Sim only made 250 pcs.The separate power supply chassis actually houses separate power supplies for the digital vs analog components, resulting in the superb clarity of detail, dynamics, and soundstaging this component is known for.
------SOLD------
Pre Amplifier

ARAGON AURUM
MADE IN USA
The Aragon Aurum is an accurate and high-quality pre-amplifier that boasts numerous features. It has a massive power supply, having more than 50,000 micorfarads of storage capacitance in the Ingot (the power supply unit), more than most power amplifiers available on the market. The pre-amplifier's unique, carefully-designed circuitry allows the user to customize the power supply to the signal path circuitry, and also eliminates crosstalk contamination of the source signal. The Aurum allows for both single-ended and balanced operation, and in balanced mode performance is enhanced when the pre-amplifier is placed at a distance away from the power amplifier. Considered to be the finest preamp made by Aragon, the Aurum is sure to provide the user with many years of listening pleasure.
-------SOLD-------
MADE IN USA
The Aragon Aurum is an accurate and high-quality pre-amplifier that boasts numerous features. It has a massive power supply, having more than 50,000 micorfarads of storage capacitance in the Ingot (the power supply unit), more than most power amplifiers available on the market. The pre-amplifier's unique, carefully-designed circuitry allows the user to customize the power supply to the signal path circuitry, and also eliminates crosstalk contamination of the source signal. The Aurum allows for both single-ended and balanced operation, and in balanced mode performance is enhanced when the pre-amplifier is placed at a distance away from the power amplifier. Considered to be the finest preamp made by Aragon, the Aurum is sure to provide the user with many years of listening pleasure.
-------SOLD-------
Pre Amplifier (Tube)

AUDIO RESEARCH LS15
MADE IN USA
The LS15 is an all-new line-level preamplifier which replaces the LS2/2BMKII series. It features all-tube gain (12 dB standard) using four 6922 twin triode tubes in a Class A, fully differential zero feedback (balanced) circuit with electronically regulated high and low-voltage supplies. The LS15 includes handheld IR remote control of all essential front-panel functions. An onboard microprocessor controls a 70-step electronic relay attenuator and 5-position input selector. An additional Direct input (balanced) provides a highest-signal-purity path for your favorite music source. A total of two balanced and five single-ended (including tape) dedicated inputs are included.
Main outputs are balanced and single-ended, with one pair of single-ended tape outputs. Spring-activated toggle switches activate electronic relays to control key functions with minimal signal degradation. Factory-set gain of 18 dB is optional at no charge. The anodized front panel is available in natural aluminum or black, cabinet style or with rack-mount holes.
------SOLD-----
MADE IN USA
The LS15 is an all-new line-level preamplifier which replaces the LS2/2BMKII series. It features all-tube gain (12 dB standard) using four 6922 twin triode tubes in a Class A, fully differential zero feedback (balanced) circuit with electronically regulated high and low-voltage supplies. The LS15 includes handheld IR remote control of all essential front-panel functions. An onboard microprocessor controls a 70-step electronic relay attenuator and 5-position input selector. An additional Direct input (balanced) provides a highest-signal-purity path for your favorite music source. A total of two balanced and five single-ended (including tape) dedicated inputs are included.
Main outputs are balanced and single-ended, with one pair of single-ended tape outputs. Spring-activated toggle switches activate electronic relays to control key functions with minimal signal degradation. Factory-set gain of 18 dB is optional at no charge. The anodized front panel is available in natural aluminum or black, cabinet style or with rack-mount holes.
------SOLD-----
Pre Amplifier

CONRAD JOHNSON PV11
MADE IN USA
Specifications:
Gain: Phono Stage 47 dB (phono overload 200 mV at 1kHz)
Line Stage 18 dB
Distortion: less than .1% THD or IMD
Response: bandpass 2Hz to more than 100kHz
RIAA equalization: +/- .25 dB (20 to 20 kHz)
S/N Ratio: Phono Stage 78 dB below 10 mv input
Line Stage 92 dB below 2.5 volt output
Phase Response: Line Stage phase inverting, Phono Stage phase correct
Mechanical: 19" X 3" x 12.5"
Features:
Inputs/Outputs — Phono,Tuner, CD, Auxiliary, Tape1, and Tape2 inputs; Rec1, Rec2, and two amplifier (Main) outputs.
Controls:
Selector, Tape 1/Tape 2, Source/Monitor, Mode (Left, Right, Stereo, Reverse, Mono), Balance, Power, and Level.
-----SOLD------
MADE IN USA
Specifications:
Gain: Phono Stage 47 dB (phono overload 200 mV at 1kHz)
Line Stage 18 dB
Distortion: less than .1% THD or IMD
Response: bandpass 2Hz to more than 100kHz
RIAA equalization: +/- .25 dB (20 to 20 kHz)
S/N Ratio: Phono Stage 78 dB below 10 mv input
Line Stage 92 dB below 2.5 volt output
Phase Response: Line Stage phase inverting, Phono Stage phase correct
Mechanical: 19" X 3" x 12.5"
Features:
Inputs/Outputs — Phono,Tuner, CD, Auxiliary, Tape1, and Tape2 inputs; Rec1, Rec2, and two amplifier (Main) outputs.
Controls:
Selector, Tape 1/Tape 2, Source/Monitor, Mode (Left, Right, Stereo, Reverse, Mono), Balance, Power, and Level.
-----SOLD------
Pre Amplifier

THRESHOLD FET ONE
MADE IN USA
It has MM and MC phono
------SOLD------
MADE IN USA
It has MM and MC phono
------SOLD------
Pre Amplifier (Tube)

AESTHETIX CALYPSO
MADE IN USA
Specifications :
Inputs: 5 line RCA or XLR (balanced), plus 1 tape, RCA or XLR
Outputs: 2 RCA (SE) and XLR (balanced), 1 tape RCA
Line level gain: 23 dB single ended (SE), in/out, and 29 dB balanced/out
Volume control: switched resistor network volume control with 88 1 dB steps
Front panel controls: main input, tape input select, volume, balance, phase, mute, display, and bypass
Remote controls: main input, tape input select, volume, balance, phase, mute, display, bypass and standby
Frequency response: +- 0.25 dB, 20 Hz - 20 Khz
Signal to noise: measured at 70 dB minimum, A-weighted (ref 1 mv input, 75 dB gain setting)
Line input impedence: 40 k ohms SE, 80 k ohms balanced
Maximum line input: 3.5 volts SE, 7.0 volts RMS balanced
Output impedence: 1K ohms SE, 600 ohms balanced
Recommended amplifier load: 10K ohms or greater (SE), 20K ohms or greater (Balanced)
Tubes, each channel: (line section) V1 (12AX7 or equivalent), V2 (6922/6DJ8)
Power consumption: 20 watts standby, 60 watts active
Physical dimensions: 4 3/8" high, 17 7/8" wide, 18" deep including jacks
Shipping weight: 40 lbs.
------SOLD------
MADE IN USA
Specifications :
Inputs: 5 line RCA or XLR (balanced), plus 1 tape, RCA or XLR
Outputs: 2 RCA (SE) and XLR (balanced), 1 tape RCA
Line level gain: 23 dB single ended (SE), in/out, and 29 dB balanced/out
Volume control: switched resistor network volume control with 88 1 dB steps
Front panel controls: main input, tape input select, volume, balance, phase, mute, display, and bypass
Remote controls: main input, tape input select, volume, balance, phase, mute, display, bypass and standby
Frequency response: +- 0.25 dB, 20 Hz - 20 Khz
Signal to noise: measured at 70 dB minimum, A-weighted (ref 1 mv input, 75 dB gain setting)
Line input impedence: 40 k ohms SE, 80 k ohms balanced
Maximum line input: 3.5 volts SE, 7.0 volts RMS balanced
Output impedence: 1K ohms SE, 600 ohms balanced
Recommended amplifier load: 10K ohms or greater (SE), 20K ohms or greater (Balanced)
Tubes, each channel: (line section) V1 (12AX7 or equivalent), V2 (6922/6DJ8)
Power consumption: 20 watts standby, 60 watts active
Physical dimensions: 4 3/8" high, 17 7/8" wide, 18" deep including jacks
Shipping weight: 40 lbs.
------SOLD------
Pre Amplifier (Tube)

ROGUE AUDIO MAGNUM 99
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
----SOLD-----
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
----SOLD-----
Pre Amplifier

GRYPHON
BEL CANTO
MADE IN DENMARK
Hi-End preamplifier GRYPHON BEL CANTO working in dual mono construction with separate power supply.
----SOLD------
BEL CANTO
MADE IN DENMARK
Hi-End preamplifier GRYPHON BEL CANTO working in dual mono construction with separate power supply.
----SOLD------
Pre Amplifier (Tube)

AUDIO RESEARCH LS26
MADE IN USA
Frequency response +0-3dB, 0.2Hz to 160kHz at rated output (Balanced, 200k ohms load)
Distortion (THD) Less than .01% at 2V RMS BAL output.
Noise & hum 1.3uV RMS residual IHF weighted balanced equivalent input noise with volume at 1 (100 dB below 2V RMS output).
Gain Main output : Selectable for each input: 24dB, 18dB, 12dB Balanced output. (18dB, 12dB, 6dB SE output.) Record output: 0dB (Processor input: 0dB balanced.)
Input impedance 120K ohms Balanced, 60K ohms SE.
Output impedance 700 ohms Balanced, 350 ohms SE Main (2). 20K ohms minimum load and 2000pF maximum capacitance.
Output polarity Non-inverting.
Maximum inputs Low Gain: 48V RMS BAL, 24V RMS SE. Medium Gain: 24V RMS BAL, 12V RMS SE. High Gain: 12V RMS BAL, 6V RMS SE.
Rated outputs 2V RMS 1Hz to 100kHz into 200K ohm balanced load (maximum balanced output capability is 15V RMS at less than 0.5% THD at 1kHz)
Power supplies Electronically-regulated low and high voltage supplies. Automatic 50 sec. warm-up/brown-out mute. Line regulation better than .01%.
Tube complement (2) 6H30 dual triode. (Hybrid JFET/tube audio circuit, solid-state power supply).
Power requirements 105-130VAC 60Hz (210-260VAC 50/60Hz) 50 watts maximum.
Other Rotary volume selector (104 steps) and rotary input selector.
Push buttons: Power, Monitor, BAL/SE, Proc, Mute.
Remote buttons: Display, Bal L, Bal R, Hours, Invert, Gain.
Dimensions 19" (48 cm) W x 5.25"(13.4 cm) H (standard rack panel) x 12"(30.5 cm) D. Handles extend 1.50" (3.8 cm) forward of the front panel.
Weight 16.5 lbs. (7.5 kg) Net; 26 lbs. (11.8 kg) Shipping.
----SOLD-----
MADE IN USA
Frequency response +0-3dB, 0.2Hz to 160kHz at rated output (Balanced, 200k ohms load)
Distortion (THD) Less than .01% at 2V RMS BAL output.
Noise & hum 1.3uV RMS residual IHF weighted balanced equivalent input noise with volume at 1 (100 dB below 2V RMS output).
Gain Main output : Selectable for each input: 24dB, 18dB, 12dB Balanced output. (18dB, 12dB, 6dB SE output.) Record output: 0dB (Processor input: 0dB balanced.)
Input impedance 120K ohms Balanced, 60K ohms SE.
Output impedance 700 ohms Balanced, 350 ohms SE Main (2). 20K ohms minimum load and 2000pF maximum capacitance.
Output polarity Non-inverting.
Maximum inputs Low Gain: 48V RMS BAL, 24V RMS SE. Medium Gain: 24V RMS BAL, 12V RMS SE. High Gain: 12V RMS BAL, 6V RMS SE.
Rated outputs 2V RMS 1Hz to 100kHz into 200K ohm balanced load (maximum balanced output capability is 15V RMS at less than 0.5% THD at 1kHz)
Power supplies Electronically-regulated low and high voltage supplies. Automatic 50 sec. warm-up/brown-out mute. Line regulation better than .01%.
Tube complement (2) 6H30 dual triode. (Hybrid JFET/tube audio circuit, solid-state power supply).
Power requirements 105-130VAC 60Hz (210-260VAC 50/60Hz) 50 watts maximum.
Other Rotary volume selector (104 steps) and rotary input selector.
Push buttons: Power, Monitor, BAL/SE, Proc, Mute.
Remote buttons: Display, Bal L, Bal R, Hours, Invert, Gain.
Dimensions 19" (48 cm) W x 5.25"(13.4 cm) H (standard rack panel) x 12"(30.5 cm) D. Handles extend 1.50" (3.8 cm) forward of the front panel.
Weight 16.5 lbs. (7.5 kg) Net; 26 lbs. (11.8 kg) Shipping.
----SOLD-----
Pre Amplifier (Tube)

AUDIO RESEARCH LS17
MADE IN USA
SPECIFICATIONS ;
Tube complement : (2) 6H30 dual triode. (Hybrid JFET/tube audio circuit,
solid-state power supply).
Power requirements : 105-130VAC 60Hz (210-260VAC 50/60Hz) 50 watts
maximum.
Other : Rotary volume selector (104 steps, 20 LED indicators) and rotary input selector.
Push buttons: Power, Monitor, Proc, Mute. Also remote buttons: Bal 1, Bal 2, Aux, Tuner, CD.
Dimensions : 19" (48 cm) W x 5.25"(13.4 cm) H (standard rack panel) x 12"(30.5 cm)
Weight : 13 lbs. (5.9 kg) Net; 23 lbs. (11.5 kg) Shipping.
----SOLD---
MADE IN USA
SPECIFICATIONS ;
Tube complement : (2) 6H30 dual triode. (Hybrid JFET/tube audio circuit,
solid-state power supply).
Power requirements : 105-130VAC 60Hz (210-260VAC 50/60Hz) 50 watts
maximum.
Other : Rotary volume selector (104 steps, 20 LED indicators) and rotary input selector.
Push buttons: Power, Monitor, Proc, Mute. Also remote buttons: Bal 1, Bal 2, Aux, Tuner, CD.
Dimensions : 19" (48 cm) W x 5.25"(13.4 cm) H (standard rack panel) x 12"(30.5 cm)
Weight : 13 lbs. (5.9 kg) Net; 23 lbs. (11.5 kg) Shipping.
----SOLD---
Pre Amplifier (Tube)

CARY SLP-308
MADE IN USA
Cary Audio SLP-308 features a nice retro look with a front panel output level meters in bluish lighting. It comes with remote volume control as a standard. SLP-308 sports 4 stereo input pairs, a Mute switch, and tape monitor loop. Finishing is either Black or Silver faceplate. As usual it has ZERO feedback design for ultimate sound.
Spesifications :
Weight : 15 lbs.
Dimensions : 6" H x 16" W x 11" D
Circuit Type : Class A Single-Ended
Gain Line Stage : 12 dB
Noise and Hum : > 88 dB below full output
Input Impedance : 100K Ohms
Output Impedance : 440 Ohms
Frequency Response : 10 Hz to 50 KHz +/- 0.5 dB
Tubes : 2 - 12AU7 dual triode vacuum tubes
Power Transformer(s) : R-Core, 200% duty cycle
Wire : EE Teflon Silver
Resistors : 1% Metal Film
Capacitors : Polypropylene
Power Supply : Full wave rectified feeding a Pi network and filter choke.
AC Cord : 3 conductor shielded detachable
AC Power Requirements : 117 or 234 VAC @ 50/60 Hz according to market
Break-In Time : 100 hours of playing time
Finish : Black steel chassis with black or silver anodized aluminum face plate, silver knobs, remote volume control, tape monitor loop, 4 stereo input pairs, all RCA connectors for inputs, outputs and the tape monitor loop, dual output level meters.
----SOLD----
MADE IN USA
Cary Audio SLP-308 features a nice retro look with a front panel output level meters in bluish lighting. It comes with remote volume control as a standard. SLP-308 sports 4 stereo input pairs, a Mute switch, and tape monitor loop. Finishing is either Black or Silver faceplate. As usual it has ZERO feedback design for ultimate sound.
Spesifications :
Weight : 15 lbs.
Dimensions : 6" H x 16" W x 11" D
Circuit Type : Class A Single-Ended
Gain Line Stage : 12 dB
Noise and Hum : > 88 dB below full output
Input Impedance : 100K Ohms
Output Impedance : 440 Ohms
Frequency Response : 10 Hz to 50 KHz +/- 0.5 dB
Tubes : 2 - 12AU7 dual triode vacuum tubes
Power Transformer(s) : R-Core, 200% duty cycle
Wire : EE Teflon Silver
Resistors : 1% Metal Film
Capacitors : Polypropylene
Power Supply : Full wave rectified feeding a Pi network and filter choke.
AC Cord : 3 conductor shielded detachable
AC Power Requirements : 117 or 234 VAC @ 50/60 Hz according to market
Break-In Time : 100 hours of playing time
Finish : Black steel chassis with black or silver anodized aluminum face plate, silver knobs, remote volume control, tape monitor loop, 4 stereo input pairs, all RCA connectors for inputs, outputs and the tape monitor loop, dual output level meters.
----SOLD----
Pre Amplifier (Tube)

CONRAD JOHNSON PV1
MADE IN USA
Specifications:
Gain: Phono Stage 35 dB (phono overload 500 mV at 1kHz)
Line Stage 28 dB
Distortion: less than .05% THD or IMD
Response: bandpass 2Hz to more than 100kHz
RIAA Equalization: +/- .25 dB (20 to 20 kHz)
S/N Ratio: Phono Stage 70 dB below 10 mv input
Line Stage 84 dB below 2.5 volt output
Phase: Phono Stage is phase correct, Line Stage is phase correct
Mechanical: 14 x 4 3/4" x 11 1/4"
---SOLD----
MADE IN USA
Specifications:
Gain: Phono Stage 35 dB (phono overload 500 mV at 1kHz)
Line Stage 28 dB
Distortion: less than .05% THD or IMD
Response: bandpass 2Hz to more than 100kHz
RIAA Equalization: +/- .25 dB (20 to 20 kHz)
S/N Ratio: Phono Stage 70 dB below 10 mv input
Line Stage 84 dB below 2.5 volt output
Phase: Phono Stage is phase correct, Line Stage is phase correct
Mechanical: 14 x 4 3/4" x 11 1/4"
---SOLD----
Pre Amplifier

MCINTOSH C35
MADE IN USA
----SOLD-----
MADE IN USA
----SOLD-----
Pre Amplifier (Tube)

VTL TL-2.5
MADE IN USA
Data Specifications :
Vacuum Tube Complement : 2 x 12AU7, 2 x 12AT7
Inputs : 6 Single ended Line inputs
2 RCA Processor / Tape in
Outputs : 2 pairs Single-ended RCA
2 pairs Processor / Tape Out
Remote Control Functions : Volume and Mute
Gain : 20 dB
Output Impedance : 200 Ohms
Input Impedance : 20K Ohms
Frequency response + 0 - 3 dB : 1 Hz - 60KHz
Maximum Output Voltage < 1% THD : 60 Volts
Channel Separation : > 75 dB @ 1KHz
Power Consumption : 100 Watts
Dimensions (W x D H) : 19 x 14 x 3.75 inches
48.25 x 35.5 x 9.5 cm
Weight : 25 lbs (11Kg) Fully packed
----SOLD---
MADE IN USA
Data Specifications :
Vacuum Tube Complement : 2 x 12AU7, 2 x 12AT7
Inputs : 6 Single ended Line inputs
2 RCA Processor / Tape in
Outputs : 2 pairs Single-ended RCA
2 pairs Processor / Tape Out
Remote Control Functions : Volume and Mute
Gain : 20 dB
Output Impedance : 200 Ohms
Input Impedance : 20K Ohms
Frequency response + 0 - 3 dB : 1 Hz - 60KHz
Maximum Output Voltage < 1% THD : 60 Volts
Channel Separation : > 75 dB @ 1KHz
Power Consumption : 100 Watts
Dimensions (W x D H) : 19 x 14 x 3.75 inches
48.25 x 35.5 x 9.5 cm
Weight : 25 lbs (11Kg) Fully packed
----SOLD---
Pre Amplifier (Tube)

COUNTERPOINT SA-2000
MADE IN USA
The unit has a single 6DJ8 line stage followed with a solid-state video buffer. There is no loop feedback Six line-level inputs plus two tape ins. Dual pairs of tape outs and main outs. Input Selector, Tape monitor, Mono/Stereo, Balance, Volume, Mute and Power controls. Solid-state power supply voltage regulator fed by vacuum-tube rectifier. Aluminum front panel finished in black anodize.
------SOLD----
MADE IN USA
The unit has a single 6DJ8 line stage followed with a solid-state video buffer. There is no loop feedback Six line-level inputs plus two tape ins. Dual pairs of tape outs and main outs. Input Selector, Tape monitor, Mono/Stereo, Balance, Volume, Mute and Power controls. Solid-state power supply voltage regulator fed by vacuum-tube rectifier. Aluminum front panel finished in black anodize.
------SOLD----
Pre Amplifier (tube)

QUICKSILVER
LINE STAGE PREAMP
MADE IN USA
The Quicksilver Line Stage Preamp embodies the Quicksilver philosophy of simplicity. It uses only one 12AX7 per channel, resulting in a very direct sound. A precision Alps attenuator, with 41 detents, is used for the volume control. The gold-plated Teflon insert RCA jacks are chassis mounted for long life. Gain is 18 db. Minimum load is 20 Kohms.
------SOLD-----
LINE STAGE PREAMP
MADE IN USA
The Quicksilver Line Stage Preamp embodies the Quicksilver philosophy of simplicity. It uses only one 12AX7 per channel, resulting in a very direct sound. A precision Alps attenuator, with 41 detents, is used for the volume control. The gold-plated Teflon insert RCA jacks are chassis mounted for long life. Gain is 18 db. Minimum load is 20 Kohms.
------SOLD-----
Pre Amplifier (Tube)

ROGUE AUDIO MAGNUM 99
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Optional mm/mc phono board
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
------SOLD----
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Optional mm/mc phono board
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
------SOLD----
Pre Amplifier (Tube)

AUDIO RESEARCH SP-16
MADE IN USA
Specifications:
Frequency response
Line: +0-1dB, 1Hz to 60kHz at rated output. -3dB points below 0.5Hz and above 100KHz
Distortion (THD)
Less than .007% at 2V RMS single ended output
Noise & hum
Line: 15µV RMS IHF weighted at main output with volume low (96dB below 1V RMS output).
Gain
Main output line: 11.5dB Single Ended Processor: 0dB
Record output, line: 0dB.
Input impedance
50K ohms line, 47K ohms Phono, (1 to 6Mv High output cartridge recommended) Inputs (6): phono, DC, tuner, video, aux, processor, (Single Ended RCA connectors). Model SP16L has no phono input.
Output impedance
260 ohms Single Ended main; 20K ohms minimum load and 1000 pF maximum capacitance. Outputs (3): 2 main, 1 record (Single Ended RCA connectors).
Output polarity
Non inverting (Any input or output).
Maximum inputs
Line: 3.5V RMS Single Ended.
Rated outputs
2V RMS Single Ended into 100K load. Maximum output 15V RMS at 1% THD at 1kHz.
Power supplies
Electronically regulated low and high voltage supplies. Automatic 30-sec. warm-up/brown-out mute. Line regulation better than .01%.
Tube complement
(6) 12AX7EH dual triodes
Power requirements
100-135VAC 60Hz (200-270VAC 50/60Hz) 36 watts.
Other
Push buttons: Volume up, volume down (70 steps, 20 LED indicators), Input, Processor, Mute, Power. All functions on IR remote control.
Remote 12V out: Line: 12V DC at 100 mA max for system power control, i.e. to turn on power amplifiers and other equipment and full remote control on all functions.
Dimensions
17.75" (45 cm) W x 5.2" (13.2 cm) H x 10.0"(25.4 cm) D. Rear connectors extend 0.6" (1.5 cm).
Weight
12.6 lbs. (5.7 kg) Net; 20 lbs. (9.1 kg) Shipping.
----SOLD----
MADE IN USA
Specifications:
Frequency response
Line: +0-1dB, 1Hz to 60kHz at rated output. -3dB points below 0.5Hz and above 100KHz
Distortion (THD)
Less than .007% at 2V RMS single ended output
Noise & hum
Line: 15µV RMS IHF weighted at main output with volume low (96dB below 1V RMS output).
Gain
Main output line: 11.5dB Single Ended Processor: 0dB
Record output, line: 0dB.
Input impedance
50K ohms line, 47K ohms Phono, (1 to 6Mv High output cartridge recommended) Inputs (6): phono, DC, tuner, video, aux, processor, (Single Ended RCA connectors). Model SP16L has no phono input.
Output impedance
260 ohms Single Ended main; 20K ohms minimum load and 1000 pF maximum capacitance. Outputs (3): 2 main, 1 record (Single Ended RCA connectors).
Output polarity
Non inverting (Any input or output).
Maximum inputs
Line: 3.5V RMS Single Ended.
Rated outputs
2V RMS Single Ended into 100K load. Maximum output 15V RMS at 1% THD at 1kHz.
Power supplies
Electronically regulated low and high voltage supplies. Automatic 30-sec. warm-up/brown-out mute. Line regulation better than .01%.
Tube complement
(6) 12AX7EH dual triodes
Power requirements
100-135VAC 60Hz (200-270VAC 50/60Hz) 36 watts.
Other
Push buttons: Volume up, volume down (70 steps, 20 LED indicators), Input, Processor, Mute, Power. All functions on IR remote control.
Remote 12V out: Line: 12V DC at 100 mA max for system power control, i.e. to turn on power amplifiers and other equipment and full remote control on all functions.
Dimensions
17.75" (45 cm) W x 5.2" (13.2 cm) H x 10.0"(25.4 cm) D. Rear connectors extend 0.6" (1.5 cm).
Weight
12.6 lbs. (5.7 kg) Net; 20 lbs. (9.1 kg) Shipping.
----SOLD----
Pre Amplifier

MOON P5.3 RS
MADE IN CANADA
Significant Design Features:
The RS series of MOON audio components benefit from an even higher standard of manufacturing process than the regular MOON versions. All significant differences are contained within the circuitry and construction of each model.
· IR input for external control (all discrete codes)
· One line input which bypasses the gain control stage to accomodate a component, such as a
home-theatre processor, whose own volume control is used instead
· An extremely short capacitor-free signal path measuring only 10 inches in length from input to
output connectors, eliminating virtually all potential sources of interference and producing a
sonically faster transient response
· An oversized power supply with 3 stages of DC voltage regulation
· Open loop zero feedback circuit topology using absolutely no capacitors
anywhere in the audio signal path
· Power supply voltage regulation includes Evolution series i²DCf (Independant Inductive DC
Filtering); There is one inductor dedicated to each integrated circuit type component (DAC,
Op-Amp, etc.) in the audio circuit’s signal path - 14 stages
· Accurate matching of the very finest high quality electronic components
· A symmetrical circuit design
· 4-Layer PCB’s with pure copper tracings for a much shorter signal path; This results in
greater sonic accuracy and a dramatically improved signal-to-noise ratio
· Extremely rigid chassis construction to minimize the effects of external vibrations
· Improved reliabilty through the elimination of moving parts
· Designed to be powered up at all times for optimal performance
· Includes FRM-2 remote control.
----SOLD---
MADE IN CANADA
Significant Design Features:
The RS series of MOON audio components benefit from an even higher standard of manufacturing process than the regular MOON versions. All significant differences are contained within the circuitry and construction of each model.
· IR input for external control (all discrete codes)
· One line input which bypasses the gain control stage to accomodate a component, such as a
home-theatre processor, whose own volume control is used instead
· An extremely short capacitor-free signal path measuring only 10 inches in length from input to
output connectors, eliminating virtually all potential sources of interference and producing a
sonically faster transient response
· An oversized power supply with 3 stages of DC voltage regulation
· Open loop zero feedback circuit topology using absolutely no capacitors
anywhere in the audio signal path
· Power supply voltage regulation includes Evolution series i²DCf (Independant Inductive DC
Filtering); There is one inductor dedicated to each integrated circuit type component (DAC,
Op-Amp, etc.) in the audio circuit’s signal path - 14 stages
· Accurate matching of the very finest high quality electronic components
· A symmetrical circuit design
· 4-Layer PCB’s with pure copper tracings for a much shorter signal path; This results in
greater sonic accuracy and a dramatically improved signal-to-noise ratio
· Extremely rigid chassis construction to minimize the effects of external vibrations
· Improved reliabilty through the elimination of moving parts
· Designed to be powered up at all times for optimal performance
· Includes FRM-2 remote control.
----SOLD---
Pre Amplifier (Tube)

CONRAD JOHNSON PV-14L
MADE IN USA
The PV14L was a remote-controlled zero-feedback vacuum-tube line-stage preamplifier with seven inputs that was designed to serve as the control center for high-performance audio and audio/video systems. The PV14L featured a level control derived from technology developed for our Premier products. It employed a microprocessor controlled stepped attenuator with discrete resistors, which offers considerable sonic advantages over the motorized carbon track potentiometers more commonly used. This arrangement also allowed the PV14L to produce precisely repeatable volume settings.
The PV14L included a Theater input/output loop much the same as was introduced in the Premier16, which provides a locked unity gain setting, made it the ideal component to integrate home theater into their stereos without compromising the performance of their primary music system.
The PV14L incorporated an all-new zero-feedback circuit based on a single stage triode amplifier using a 6C4 miniature vacuum tube. A direct coupled buffer stage provided a low output impedance.
Specifications :
Gain: 22 dB
Maximum Output: 10.0 vrms
Distortion: less than .25% THD
Freq. Response: 2 Hz to 100 KHz +0/-1 dB
Hum and Noise: 98 dB below 2.5 V
Phase: phase inverting
Dimensions: 14.375D x 19W x 3.315H inches
Weight: 14 lbs.
----SOLD----
MADE IN USA
The PV14L was a remote-controlled zero-feedback vacuum-tube line-stage preamplifier with seven inputs that was designed to serve as the control center for high-performance audio and audio/video systems. The PV14L featured a level control derived from technology developed for our Premier products. It employed a microprocessor controlled stepped attenuator with discrete resistors, which offers considerable sonic advantages over the motorized carbon track potentiometers more commonly used. This arrangement also allowed the PV14L to produce precisely repeatable volume settings.
The PV14L included a Theater input/output loop much the same as was introduced in the Premier16, which provides a locked unity gain setting, made it the ideal component to integrate home theater into their stereos without compromising the performance of their primary music system.
The PV14L incorporated an all-new zero-feedback circuit based on a single stage triode amplifier using a 6C4 miniature vacuum tube. A direct coupled buffer stage provided a low output impedance.
Specifications :
Gain: 22 dB
Maximum Output: 10.0 vrms
Distortion: less than .25% THD
Freq. Response: 2 Hz to 100 KHz +0/-1 dB
Hum and Noise: 98 dB below 2.5 V
Phase: phase inverting
Dimensions: 14.375D x 19W x 3.315H inches
Weight: 14 lbs.
----SOLD----
Pre Amplifier (Tube)

BALANCED AUDIO TECHNOLOGY VK.5i
MADE IN USA
The VK-5i is a non-phase inverting, fully balanced, single chassis tubed preamplifier, utilizing eight (8) 6922 and two (2) 5881 vacuum tubes in plate-loaded triode operation. The preamp offers 5 XLR line-level inputs and 3 XLR outputs (2 main, 1 tape). Output gain is rated at 18 dB (with approximately 180 joules of energy storage). Input impedance is rated at 100 kW , with minimum power amplifier impedance rated at 10kW . Remote control is optional and controls only volume and mute functions. For single-ended inputs and outputs.
---SOLD---
MADE IN USA
The VK-5i is a non-phase inverting, fully balanced, single chassis tubed preamplifier, utilizing eight (8) 6922 and two (2) 5881 vacuum tubes in plate-loaded triode operation. The preamp offers 5 XLR line-level inputs and 3 XLR outputs (2 main, 1 tape). Output gain is rated at 18 dB (with approximately 180 joules of energy storage). Input impedance is rated at 100 kW , with minimum power amplifier impedance rated at 10kW . Remote control is optional and controls only volume and mute functions. For single-ended inputs and outputs.
---SOLD---
Pre Amplifier (Tube)

ROGUE AUDIO MAGNUM 99
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
-----SOLD----
MADE IN USA
General Features:
- All tube mu-follower circuit topology
- Metal remote volume control
- Massive fully regulated high voltage supply
- Mono, mute, and record functions
- Separate power supply chassis
- Slow-start automated logical turn-on
- (4) 6SN7 tube complement line stage
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Heavy machined aluminum faceplate
- Heavy (2 ounce) copper circuit board
- Toroidal high voltage supply
- Headphone jack
- Entirely designed and built in the U.S.A.
-----SOLD----
Pre Amplifier (Tube)

QUAD QC-24
Quad QC-twenty-four
The QC-twenty-four Control amplifier utilises a completely new circuit design. The preamplifier is designed around the 6111WA double triode valve, designed originally for military use, the valve is hard wired into the circuit and has an estimated lifetime of 100,000 hours. Specially designed transformers and relay input switching, result in the input signal being preserved in its purest form. The QC twenty-four has 5 line level inputs including a MM Phono stage and 2 buffered tape loops.
Specification :
Valve Type 1 x 6111 NOS twin triode
THD <0.2% @ 1V RMS, 0.02% @ 1W
Frequency Response 5Hz - 50kHz (=0dB/-0.5dB)
Hum and Noise Better than -80dB
Line Stage Gain 15dB
Recommended Min Load 50k ohms
Inputs 5 x Line level
2 Buffered tape loops
----SOLD---
Quad QC-twenty-four
The QC-twenty-four Control amplifier utilises a completely new circuit design. The preamplifier is designed around the 6111WA double triode valve, designed originally for military use, the valve is hard wired into the circuit and has an estimated lifetime of 100,000 hours. Specially designed transformers and relay input switching, result in the input signal being preserved in its purest form. The QC twenty-four has 5 line level inputs including a MM Phono stage and 2 buffered tape loops.
Specification :
Valve Type 1 x 6111 NOS twin triode
THD <0.2% @ 1V RMS, 0.02% @ 1W
Frequency Response 5Hz - 50kHz (=0dB/-0.5dB)
Hum and Noise Better than -80dB
Line Stage Gain 15dB
Recommended Min Load 50k ohms
Inputs 5 x Line level
2 Buffered tape loops
----SOLD---
Pre Amplifier

KRELL PAM5
MADE IN USA
Krell PAM-5 full function stereo preamp with phono stage. Grey finish with elegant, low profile. Build quality and workmanship is very high, typical of Krell. A real handsome preamp. Krell is all about pride of ownership, pure and simple. Your ticket to a true high end preamp. beautiful piece of equipment. With separate power supply 4 RCA inputs + Tape 2 RCA outputs.
----SOLD---
MADE IN USA
Krell PAM-5 full function stereo preamp with phono stage. Grey finish with elegant, low profile. Build quality and workmanship is very high, typical of Krell. A real handsome preamp. Krell is all about pride of ownership, pure and simple. Your ticket to a true high end preamp. beautiful piece of equipment. With separate power supply 4 RCA inputs + Tape 2 RCA outputs.
----SOLD---
Pre Amplifier (Tube)

KORA EQUINOXE
MADE IN FRANCE
Kora Equinoxe tubed line stage with black & chrome faceplate with gold accents.. Excellent French-made preamp with built-in phonostage, HT bypass and remote
---SOLD--
MADE IN FRANCE
Kora Equinoxe tubed line stage with black & chrome faceplate with gold accents.. Excellent French-made preamp with built-in phonostage, HT bypass and remote
---SOLD--
Pre Amplifier

VENTURE AUDIO MY TOY
MADE IN BELGIUM
Specifications :
Impedance: 10 kOhm
Attenuator: Film potentiometer
Wiring inside: Venture Micro Reference Cable.
Input/Output: 1 set, WBT.
Knob: Solid brass, 24 K gold plated.
Marking: Genuine Ruby stone on gold
---SOLD---
MADE IN BELGIUM
Specifications :
Impedance: 10 kOhm
Attenuator: Film potentiometer
Wiring inside: Venture Micro Reference Cable.
Input/Output: 1 set, WBT.
Knob: Solid brass, 24 K gold plated.
Marking: Genuine Ruby stone on gold
---SOLD---
Pre Amplifier

CAIRN NANDA
MADE IN FRANCE
Technical specifications:
• Steel chassis with feet of antivibrational aluminium
• Solid aluminum knobs
• Three transformers, for a total of 410 VA
• Maximum output level (VRMS): 10
• Dynamic range: 110 db
• Gain: 17 db
• Output impedance: 50 ohm
• Dimensions: 43 x 8 x 31 cm (WxHxD)
• Weight: 12 Kg
----SOLD---
MADE IN FRANCE
Technical specifications:
• Steel chassis with feet of antivibrational aluminium
• Solid aluminum knobs
• Three transformers, for a total of 410 VA
• Maximum output level (VRMS): 10
• Dynamic range: 110 db
• Gain: 17 db
• Output impedance: 50 ohm
• Dimensions: 43 x 8 x 31 cm (WxHxD)
• Weight: 12 Kg
----SOLD---
Pre Amplifier

THRESHOLD FET TEN/e
MADE IN USA
----SOLD---
MADE IN USA
----SOLD---
Pre Amplifier (Tube)

CANARY AUDIO CA-601
MADE IN USA
Specifications :
Input Impedance: 50,000 Ohms min, 95,000 Ohms max.
Output Impedance: 650 Ohms
Maximum Gain: 13.5 dB
Frequency Response: +/- 1 dB from 10 Hz to 64,000 Hz
Hum and Noise: 80 dB
Maximum Output Voltage before clipping: 130 Volts
Total Harmonic Distortion: < 0.06%
Power Consumption: 22 Watts (true RMS)
Tube Complement: 2 x 6922
1 x 6CG7
Dimensions: 18.5" W x 13" D x 2.5" H
Net Weight: 18 lbs
----SOLD---
MADE IN USA
Specifications :
Input Impedance: 50,000 Ohms min, 95,000 Ohms max.
Output Impedance: 650 Ohms
Maximum Gain: 13.5 dB
Frequency Response: +/- 1 dB from 10 Hz to 64,000 Hz
Hum and Noise: 80 dB
Maximum Output Voltage before clipping: 130 Volts
Total Harmonic Distortion: < 0.06%
Power Consumption: 22 Watts (true RMS)
Tube Complement: 2 x 6922
1 x 6CG7
Dimensions: 18.5" W x 13" D x 2.5" H
Net Weight: 18 lbs
----SOLD---
Pre Amplifier (Tube)

AUDIO NOTE
M-ZERO
MADE IN UK
Zero chassis style line pre-amplifier with 5 inputs, tape loop and two outputs, no feedback 6111WA dual triode output stage.
---SOLD---
M-ZERO
MADE IN UK
Zero chassis style line pre-amplifier with 5 inputs, tape loop and two outputs, no feedback 6111WA dual triode output stage.
---SOLD---
Pre Amplifier (Tube)

AUDIO RESEARCH SP6B
MADE IN USA
Preamplifier Tube Audio Research SP6B, one of the legendary and best product ever from Audio Research USA with 6tube 12AX7, deliver warm, musicality result, all Mullard tube was in shape condition
----SOLD---
MADE IN USA
Preamplifier Tube Audio Research SP6B, one of the legendary and best product ever from Audio Research USA with 6tube 12AX7, deliver warm, musicality result, all Mullard tube was in shape condition
----SOLD---
Pre Amplifier (Tube)

ROGUE AUDIO PERSEUS
MADE IN USA
General Features:
- Four tube mu-follower design
- Massive power supply
- Slow start turn on sequencing
- Auto mute at turn on/turn off
- Home Theater bypass
- Subwoofer output
- Metal remote volume
- Heavy duty gold plated RCA inputs
- Machined aluminum faceplate and knobs
- All precision components
- Individually regulated filament supplies
- Alps volume and balance controls
- 4 input selections (Phono, CD, Tuner, Aux)
- 1 Home Theater input
- 3 outputs (1 fixed, 2 variable)
- 40 - 65 dB gain phono stage
- RIAA equalization within 0.25 DB
- User adjustable cartridge loading
- Detachable IEC power cord
- Fully tested, burned in and auditioned
- 3 year limited warranty (6 months on tubes)
- Proudly hand crafted in the USA
Specifications:
- Frequency response 5Hz – 50KHz +/- 1 dB
- THD <0.1%
- Gain line stage: 12 dB
- Gain phono stage: 65 dB
- Rated output: 1.5V RMS
- Output impedance: 450 ohms
- Maxcimum output: 20V RMS
- RIAA accuracy = +/- 0.25 dB
- Dimensions 18 ”W X 4.5 ”H X 14.5” D
- Weight 22 pounds
- Power requirements 115/230V – 50/50Hz
-----SOLD----
MADE IN USA
General Features:
- Four tube mu-follower design
- Massive power supply
- Slow start turn on sequencing
- Auto mute at turn on/turn off
- Home Theater bypass
- Subwoofer output
- Metal remote volume
- Heavy duty gold plated RCA inputs
- Machined aluminum faceplate and knobs
- All precision components
- Individually regulated filament supplies
- Alps volume and balance controls
- 4 input selections (Phono, CD, Tuner, Aux)
- 1 Home Theater input
- 3 outputs (1 fixed, 2 variable)
- 40 - 65 dB gain phono stage
- RIAA equalization within 0.25 DB
- User adjustable cartridge loading
- Detachable IEC power cord
- Fully tested, burned in and auditioned
- 3 year limited warranty (6 months on tubes)
- Proudly hand crafted in the USA
Specifications:
- Frequency response 5Hz – 50KHz +/- 1 dB
- THD <0.1%
- Gain line stage: 12 dB
- Gain phono stage: 65 dB
- Rated output: 1.5V RMS
- Output impedance: 450 ohms
- Maxcimum output: 20V RMS
- RIAA accuracy = +/- 0.25 dB
- Dimensions 18 ”W X 4.5 ”H X 14.5” D
- Weight 22 pounds
- Power requirements 115/230V – 50/50Hz
-----SOLD----
Pre Amplifier

MARK LEVINSON
LNP2
MADE IN USA
---SOLD---
LNP2
MADE IN USA
---SOLD---
Pre Amplifier

_JEFF ROWLAND
COHERENCE ONE
MADE IN USA
Coherence 1 Specs :
Inputs Phono + 3 unbalanced line
Main outputs (per channel) 1 inverting, 1 non-inverting
Dimensions 12.5 in. W x 19 in. D x 3.75 in. H
31.8 cm W x 48.3 cm D x 9.5 cm H
Weight 29 lbs., 13 kg
Gain 60 dB
Frequency Response 0.15 Hz to 220 kHz, -3 dB
RIAA Accuracy 20 Hz to 20 kHz ± 0.15 dB; +0, -3 dB, 200 kHz
Input Impedance User selectable: 0-200 ohms adjustable, 47 k ohm fixed or any value.
THD and Noise < 0.025% @ 1 kHz, 0.7 V RMS output
Max Output Level 18 V RMS
Gain 19 dB
Frequency Response 0.06 Hz to 650 kHz, -3 dB
Input Impedance 10 k ohms
Output Impedance 300 ohms (single-ended output)
600 ohms (balanced output)
THD and Noise < 0.010% @ 1 kHz, 3 V RMS output
-----SOLD---
COHERENCE ONE
MADE IN USA
Coherence 1 Specs :
Inputs Phono + 3 unbalanced line
Main outputs (per channel) 1 inverting, 1 non-inverting
Dimensions 12.5 in. W x 19 in. D x 3.75 in. H
31.8 cm W x 48.3 cm D x 9.5 cm H
Weight 29 lbs., 13 kg
Gain 60 dB
Frequency Response 0.15 Hz to 220 kHz, -3 dB
RIAA Accuracy 20 Hz to 20 kHz ± 0.15 dB; +0, -3 dB, 200 kHz
Input Impedance User selectable: 0-200 ohms adjustable, 47 k ohm fixed or any value.
THD and Noise < 0.025% @ 1 kHz, 0.7 V RMS output
Max Output Level 18 V RMS
Gain 19 dB
Frequency Response 0.06 Hz to 650 kHz, -3 dB
Input Impedance 10 k ohms
Output Impedance 300 ohms (single-ended output)
600 ohms (balanced output)
THD and Noise < 0.010% @ 1 kHz, 3 V RMS output
-----SOLD---
Pre Amplifier (Tube)

SONIC FRONTIERS SFL2
MADE IN CANADA
Specifications :
Frequency response : 20Hz...100Khz (± 0,5dB ; 100kOhm load) > 350Khz (-3dB)
THD : < 0,1% (20Hz...20Khz ; 1V output) < 0,03% (typical ; 1Khz)
Gain : 22dB @ 1Khz (single-ended) 28dB @ 1Khz (balanced)
Residual noise : 120µV unweighted (balanced out ; volume @ 12 o'clock) -85dB @ 2V RMS output
IMD : < 0,05% @ 2V output < 0,03% @ 2V output (balanced)
Input impedance : 50kOhm (single-ended) 100kOhm (balanced)
Output impedance : 160 Ohm @ 1Khz (single-ended) 320 Ohm @ 1Khz (balanced)
Minimum recommended load : 10kOhm
Output voltage : 30V RMS max. (s-e ; 100kOhm / 100pF load) 60V RMS max. (bal ; 10kOhm / 1000pF load)
Maximum input : 2,5V RMS (volume fully clockwise)
Stereo separation : 70dB @ 1Khz (single-ended) 75dB @ 1Khz (balanced)
Tubes : 8x 6922 (6DJ8 type)
PC : 75VA (standby) 135VA (max.)
Dimensions : 48 x 11,5 x 33cm (each chassis)
Weight : 25kg.
----SOLD---
MADE IN CANADA
Specifications :
Frequency response : 20Hz...100Khz (± 0,5dB ; 100kOhm load) > 350Khz (-3dB)
THD : < 0,1% (20Hz...20Khz ; 1V output) < 0,03% (typical ; 1Khz)
Gain : 22dB @ 1Khz (single-ended) 28dB @ 1Khz (balanced)
Residual noise : 120µV unweighted (balanced out ; volume @ 12 o'clock) -85dB @ 2V RMS output
IMD : < 0,05% @ 2V output < 0,03% @ 2V output (balanced)
Input impedance : 50kOhm (single-ended) 100kOhm (balanced)
Output impedance : 160 Ohm @ 1Khz (single-ended) 320 Ohm @ 1Khz (balanced)
Minimum recommended load : 10kOhm
Output voltage : 30V RMS max. (s-e ; 100kOhm / 100pF load) 60V RMS max. (bal ; 10kOhm / 1000pF load)
Maximum input : 2,5V RMS (volume fully clockwise)
Stereo separation : 70dB @ 1Khz (single-ended) 75dB @ 1Khz (balanced)
Tubes : 8x 6922 (6DJ8 type)
PC : 75VA (standby) 135VA (max.)
Dimensions : 48 x 11,5 x 33cm (each chassis)
Weight : 25kg.
----SOLD---
Pre Amplifier (Tube)

ROGUE AUDIO
MAGNUM 66
MADE IN USA
General Features:
- All tube w/phono or line stage with remote
- Separate power supply chassis
- Fully regulated high voltage supply
- Noble volume and balance controls
- 6 input selections (CD, phono, tuner, tape, aux 1, aux 2)
- Power, mute, and record buttons
- (2) 12AU7, (4) 6DJ8/6922 tube complement
- Heavy-duty gold plated RCA inputs
- Machined aluminum faceplate and knobs
- All precision components
- Heavy (2 ounce) copper circuit board
- Detachable power cord
- Fully tested, burned in, and auditioned
Specifications:
- frequency response: 10Hz-100KHz ± 1dB
- THD: <0.1%
- gain: line stage: 23dB
- gain - phono stage: 40dB
- rated output: 1.5V RMS
- output impedance: 650 Ohms
- maximum output: 30V RMS
- RIAA accuracy: ±.25dB
- dimensions: 14"W x 5½"H x 10¾"D
- power requirements: 115/230V - 50/60Hz
----SOLD---
MAGNUM 66
MADE IN USA
General Features:
- All tube w/phono or line stage with remote
- Separate power supply chassis
- Fully regulated high voltage supply
- Noble volume and balance controls
- 6 input selections (CD, phono, tuner, tape, aux 1, aux 2)
- Power, mute, and record buttons
- (2) 12AU7, (4) 6DJ8/6922 tube complement
- Heavy-duty gold plated RCA inputs
- Machined aluminum faceplate and knobs
- All precision components
- Heavy (2 ounce) copper circuit board
- Detachable power cord
- Fully tested, burned in, and auditioned
Specifications:
- frequency response: 10Hz-100KHz ± 1dB
- THD: <0.1%
- gain: line stage: 23dB
- gain - phono stage: 40dB
- rated output: 1.5V RMS
- output impedance: 650 Ohms
- maximum output: 30V RMS
- RIAA accuracy: ±.25dB
- dimensions: 14"W x 5½"H x 10¾"D
- power requirements: 115/230V - 50/60Hz
----SOLD---
Pre Amplifier (Tube)

COUNTERPOINT SA-11
MADE IN USA
Technical Summary: The unit uses 6SN7 octal tubes for the audio path. Power supply tubes are 5R4GB, 6080, 6GC5, 6JC6A, 5651 tubes. There is no feedback. Eight line inputs, tape loop, direct and buffered outputs. Tape Monitor, Tape Send, Program Source, Absolute Phase, Hi/Low Gain, Stereo/Mono, Remote Enable, Output Level, Mute, On/Off, Balance, Volume controls. Volume and balance are switched resistor arrays driven by stepper motor. Direct and Aluminum front panel finished in black or silver anodize. Original Retail Price: $7595
---SOLD---
MADE IN USA
Technical Summary: The unit uses 6SN7 octal tubes for the audio path. Power supply tubes are 5R4GB, 6080, 6GC5, 6JC6A, 5651 tubes. There is no feedback. Eight line inputs, tape loop, direct and buffered outputs. Tape Monitor, Tape Send, Program Source, Absolute Phase, Hi/Low Gain, Stereo/Mono, Remote Enable, Output Level, Mute, On/Off, Balance, Volume controls. Volume and balance are switched resistor arrays driven by stepper motor. Direct and Aluminum front panel finished in black or silver anodize. Original Retail Price: $7595
---SOLD---
Pre Amplifier

JEFF ROWLAND
COHERENCE ONE
MADE IN USA
----SOLD---
COHERENCE ONE
MADE IN USA
----SOLD---
Pre Amplifier (Tube)

SYNTHESIS HARMONY
MADE IN ITALY
Specifications :
Input : 4 line
Output : 1 rec 1 pre
Input impedance : 100 Kohm
Output impedance : 1,5 Kohm
Frequency reseponse ; 20Hz to 20Khz 0dB
Phase : Inverted
Tube Compliment : 4 x 12AU7
Dimensions (w,d,h) : 320x220x120mm
Weight : 5 Kg
---SOLD---
MADE IN ITALY
Specifications :
Input : 4 line
Output : 1 rec 1 pre
Input impedance : 100 Kohm
Output impedance : 1,5 Kohm
Frequency reseponse ; 20Hz to 20Khz 0dB
Phase : Inverted
Tube Compliment : 4 x 12AU7
Dimensions (w,d,h) : 320x220x120mm
Weight : 5 Kg
---SOLD---
Pre Amplifier

AUDIO RESEARCH
LS3
MADE IN USA
---SOLD---
LS3
MADE IN USA
---SOLD---
Pre Amplifier

THULE
SPIRIT PR150B
MADE IN DENMARK
PR150B is Thule Audio's most advanced dedicated stereo pre-amplifier.
PR150B features super-precision volume controls and specially selected Burr-Brown high-end op-amps.
PR150B has built-in cross-coupled balanced/unbalanced converters that via a technically advanced switch matrix can handle any combination of balanced or unbalanced inputs with balanced or unbalanced outputs.
Together with PA150B, you can obtain a superb fully balanced high-end power and pre-amplifier combination at a surprisingly modest price.
---SOLD---
SPIRIT PR150B
MADE IN DENMARK
PR150B is Thule Audio's most advanced dedicated stereo pre-amplifier.
PR150B features super-precision volume controls and specially selected Burr-Brown high-end op-amps.
PR150B has built-in cross-coupled balanced/unbalanced converters that via a technically advanced switch matrix can handle any combination of balanced or unbalanced inputs with balanced or unbalanced outputs.
Together with PA150B, you can obtain a superb fully balanced high-end power and pre-amplifier combination at a surprisingly modest price.
---SOLD---
Pre Amplifier (Tube)

COUNTERPOINT SA 3.1
MADE IN USA
Technical Summary:
Pure tube signal path. The unit has two 6DJ8 tubes in the phono stage and a single 6DJ8 in the line stage. As with all Counterpoint preamps, there are two gain stages in the phono section with passive riaa equalization. The line stage is a single-stage. There is no loop feedback. Solid-state power supply. Four line-level inputs, two sets of tape outputs and one set of Main outputs. Input Selector (listen), Input Selector (tape send), Gain, Balance, Stereo-mono, On-Off controls. Aluminum front panel finished in black or silver anodize. Discontinued middle of 1990.
---SOLD---
MADE IN USA
Technical Summary:
Pure tube signal path. The unit has two 6DJ8 tubes in the phono stage and a single 6DJ8 in the line stage. As with all Counterpoint preamps, there are two gain stages in the phono section with passive riaa equalization. The line stage is a single-stage. There is no loop feedback. Solid-state power supply. Four line-level inputs, two sets of tape outputs and one set of Main outputs. Input Selector (listen), Input Selector (tape send), Gain, Balance, Stereo-mono, On-Off controls. Aluminum front panel finished in black or silver anodize. Discontinued middle of 1990.
---SOLD---
Pre Amplifier (Tube)

AUDIO RESEARCH SP9
MADE IN USA
---SOLD---
MADE IN USA
---SOLD---
Pre Amplifier

PS AUDIO
PCA2
Features
PCA2
Features
- Class A zero feedback gain stage
- Optional external power supply
- Optional phono stage available
- 7 inputs
- 2 sets of outputs
- Headphone amplifier
- Balanced and single ended inputs and outputs
- Remote control
- State of the art attenuator
- Assignable input names
- Individual gain adjust per input
- Home Theater Bypass loop
- Fully balanced
- PS Buss
Pre Amplifier

AUDIO ANALOGUE
BELLINI
MADE IN ITALY
The Bellini preamplifier embodies the ideal that led to the creation of the "Great Composers" line: to offer very high quality at an affordable price. After having become a "best buy" in the markets throughout the world, now it renews its success with the new "remote" version. The Bellini was made on the basis of concepts that usually belong to higher class and cost equipments.
The power supply is splitted to the two channels since from the transformer’s outputs. The input selection is performed via relays very close to the input sockets to reduce the signal path. Differently from many other products of the same price range, the Bellini features a sophisticated FET input preamplifying circuit to treat the delicate input signals at their best, as well as a separate tape bar with tape output buffer, to optimize the tape interface. The Bellini’s "pre" output allows for biamping thanks to two pairs of RCA connectors in parallel fashion and to a noticeable current capability. While many designs avoid featuring phono inputs, Audio Analogue has given the Bellini a sophisticated RIAA preamp able to treat both moving magnet (MM) and moving coil (MC) cartridges. The new totally dicrete line circuit offers all is needed to achieve a great sound: low feedback and wide open-loop bandwidth, high current delivery, low noise and high quality components, starting from the gold plated input RCAs, to the gold plated silver body relays, up to the highest speed supply capacitors.
---SOLD---
BELLINI
MADE IN ITALY
The Bellini preamplifier embodies the ideal that led to the creation of the "Great Composers" line: to offer very high quality at an affordable price. After having become a "best buy" in the markets throughout the world, now it renews its success with the new "remote" version. The Bellini was made on the basis of concepts that usually belong to higher class and cost equipments.
The power supply is splitted to the two channels since from the transformer’s outputs. The input selection is performed via relays very close to the input sockets to reduce the signal path. Differently from many other products of the same price range, the Bellini features a sophisticated FET input preamplifying circuit to treat the delicate input signals at their best, as well as a separate tape bar with tape output buffer, to optimize the tape interface. The Bellini’s "pre" output allows for biamping thanks to two pairs of RCA connectors in parallel fashion and to a noticeable current capability. While many designs avoid featuring phono inputs, Audio Analogue has given the Bellini a sophisticated RIAA preamp able to treat both moving magnet (MM) and moving coil (MC) cartridges. The new totally dicrete line circuit offers all is needed to achieve a great sound: low feedback and wide open-loop bandwidth, high current delivery, low noise and high quality components, starting from the gold plated input RCAs, to the gold plated silver body relays, up to the highest speed supply capacitors.
---SOLD---
Pre Amplifier (Tube)

SONIC FRONTIERS
LINE 1
MADE IN CANADA
----SOLD----
LINE 1
MADE IN CANADA
----SOLD----
Pre Amplifier (Tube)

COUNTERPOINT SA 7.1
MADE IN USA
SA 7.1 features all-tube phono and line stages. As manufactured, has sufficient gain for MC cartridges but signal-to-noise not really good enough for MC use.
The unit has two 12AX7 tubes in the phono stage and originally had two 12AY7's in the line stage. Later versions used a two 6DJ8's in the line stage to overcome a tendency of the older tube to "whistle." As with all Counterpoint preamps, there are two gain stages in the phono section with passive riaa equalization. All versions (12AY7 line stage, and the first versions of the 6DJ8 design) have a gain stage followed by a cathode-follower. Later units have a MOSFET source-follower after the 6DJ8 gain stage. There is no loop feedback Three line-level inputs. There are single pairs of tape out and main out. Input Selector, Tape monitor, Balance, Volume, Mute and Power controls. Aluminum front panel finished in black or silver anodize
---SOLD---
MADE IN USA
SA 7.1 features all-tube phono and line stages. As manufactured, has sufficient gain for MC cartridges but signal-to-noise not really good enough for MC use.
The unit has two 12AX7 tubes in the phono stage and originally had two 12AY7's in the line stage. Later versions used a two 6DJ8's in the line stage to overcome a tendency of the older tube to "whistle." As with all Counterpoint preamps, there are two gain stages in the phono section with passive riaa equalization. All versions (12AY7 line stage, and the first versions of the 6DJ8 design) have a gain stage followed by a cathode-follower. Later units have a MOSFET source-follower after the 6DJ8 gain stage. There is no loop feedback Three line-level inputs. There are single pairs of tape out and main out. Input Selector, Tape monitor, Balance, Volume, Mute and Power controls. Aluminum front panel finished in black or silver anodize
---SOLD---
Pre Amplifier

ROTEL RC-1070
Remote control stereo preamp with mm/mc phono
Optimized for the real-world audiophile who demands flexibility and sound quality at an affordable price, the RC-1070 preamplifier delivers an extraordinary level of satisfaction. Featuring traditional Rotel engineering prowess, this unit features a power supply based on a custom-made toroidal transformer.The RC-1070 features six line-level inputs in addition to a phono input for moving magnet cartridges. A convenient contour control allows easy and repeatable timbre adjustments. With two sets of main outputs, a 12 volt "trigger" jack, and a Rotel-system remote control for both the pre-amplifier and a companion Rotel CD, tuner, or DVD player, the RC-1070 brings the flexibility and sound quality of Rotel separates within easy reach.
---SOLD---
Remote control stereo preamp with mm/mc phono
Optimized for the real-world audiophile who demands flexibility and sound quality at an affordable price, the RC-1070 preamplifier delivers an extraordinary level of satisfaction. Featuring traditional Rotel engineering prowess, this unit features a power supply based on a custom-made toroidal transformer.The RC-1070 features six line-level inputs in addition to a phono input for moving magnet cartridges. A convenient contour control allows easy and repeatable timbre adjustments. With two sets of main outputs, a 12 volt "trigger" jack, and a Rotel-system remote control for both the pre-amplifier and a companion Rotel CD, tuner, or DVD player, the RC-1070 brings the flexibility and sound quality of Rotel separates within easy reach.
---SOLD---